Advertisement
GRAFIX setup:
**GRAFIX systems can be configured with the Dakota Digital app for Apple and Android devices**
GRAFIX Operations
•
With the vehicle stopped, tap the Control Knob to enter the Main Menu
o
The Main menu can be entered with the vehicle moving, but only the speedometer ADJUST menu will be
available in the SETUP menu
•
Twist the Control Knob clockwise until SETUP is highlighted. Tap the knob to enter the SETUP menu.
•
You may skip to whichever reading you'd like to configure below; they do not need to be done in order.
•
After making a selection, select BACK to save and return to the main menu, then select EXIT to return to normal
operation.
•
Twisting the Control Knob clockwise moves up ↑ the menu list, twisting counterclockwise moves down ↓ the menu
list.
Obtaining speed from the BIM-01-2-FTCH
•
Twist the Control Knob clockwise until SPEED is highlighted. Tap the knob to enter SPEED menu.
•
Twist the Control Knob clockwise until INPUT is highlighted. Tap the knob to enter INPUT menu.
•
SIGNAL will be displayed. Tap the Control Knob to enter SIGNAL menu.
•
Twist the Control Knob clockwise until BIM is highlighted. Tap the knob to select BIM.
•
When SIGNAL is displayed again, twist the Control Knob until BACK is displayed, then tap to return to INPUT.
•
When INPUT is displayed again, twist the Control Knob until BACK is displayed, then tap to return to SPEED.
•
When SPEED is displayed again, twist the Control Knob until BACK is displayed, then tap to return to SETUP.
•
When SETUP is displayed again, twist the Control Knob until BACK is displayed, then tap to exit.
o
NOTE: The AUTO CAL, auto calibration, is not accessible.
o
To adjust speed, enter SETUP, enter SPEED, then enter the ADJUST menu.
▪
▪
▪
▪
▪
o
The Dakota Digital Automotive app can also be used either while driving or not driving.
Obtaining RPM from the BIM-01-2-FTCH
•
Twist the Control Knob clockwise until TACH is highlighted. Tap the knob to enter TACH menu.
•
INPUT will be displayed. Tap the Control Knob to enter INPUT menu.
•
CYLINDER will be displayed. Tap the Control Knob to enter CYLINDER menu.
•
Twist the Control Knob counterclockwise until BIM is highlighted. Tap the knob to select BIM.
•
When INPUT is displayed again, twist the Control Knob until BACK is displayed, then tap to return to TACH.
•
When TACH is displayed again, twist the Control Knob until BACK is displayed, then tap to return to SETUP.
•
When SETUP is displayed again, twist the Control Knob until BACK is displayed, then tap to exit.
Obtaining engine temperature from the BIM-01-2-FTCH
•
Twist the Control Knob clockwise until WATER is highlighted. Tap the knob to enter WATER menu.
•
INPUT will be displayed. Tap the Control Knob to enter INPUT menu.
•
Twist the Control Knob counterclockwise until BIM is highlighted. Tap the knob to select BIM.
•
When INPUT is displayed again, twist the Control Knob until BACK is displayed, then tap to return to WATER.
•
When WATER is displayed again, twist the Control Knob until BACK is displayed, then tap to return to SETUP.
•
When SETUP is displayed again, twist the Control Knob until BACK is displayed, then tap to exit.
TIP: Intake/manifold air temp, air fuel ratio, trans fluid temp, and boost will be displayed if selected in the
LAYOUTS>>GAUGES menu
(N/A on TBI system)
While driving a known speed, twisting the Control knob clockwise/counterclockwise can adjust
speed.
•
Percentage can also be adjusted without driving.
Twist the Control Knob clockwise to increment up to 125%.
Twist the Control Knob counterclockwise to decrement down to 75%.
Once the speed is correct, twist the Control Knob until BACK is displayed, then tap the knob.
You may now continue to exit the setup menu.
[6]
MAN #650819A
Advertisement
