Advertisement
VHX Setup:
Entering the VHX setup is done by holding SW1 (I) and turning the ignition to "on", or "acc".
Once in setup, one can move between speed, tach, volt, water, etc.... by tapping SW1 (I)
If you are setting multiple items, once done with one section you will automatically move onto the next item.
Obtaining speed from the BIM-01-2-FTCH
•
Hold the SW1 (I) switch from the instrument system control box while turning the key on.
o
The message display should show SETUP.
•
Release SW1 (I) - LCD1 should show SETUP SPEED.
•
Press and hold SW1 (I) for at least 3 seconds until SPEED SENDER is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until SENDER is displayed.
•
Release the switch and SENDER NORMAL will be displayed.
•
Tap SW1 (I) until SENDER BUS is displayed.
•
Press and hold SW1 (I) until DONE is displayed.
o
NOTE: The AUTO, auto calibration, is removed.
o
Speed can only be fine-tuned with the ADJUST mode at a standstill.
o
ADJUST now only alters the percentage of speed by +/- 25%.
▪
▪
▪
▪
•
Tap SW1 (I) until SPEED DONE is displayed.
•
Press and hold SW1 (I) until a big DONE is displayed.
Obtaining RPM from the BIM-01-2-FTCH
•
Hold the SW1 (I) switch from the instrument system control box while turning the key on.
o
The message display should show SETUP.
•
Release SW1 (I) - LCD1 should show SETUP SPEED.
•
Tap SW1 (I) until SETUP TACH is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until TACH ENGINE is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until ENGINE is displayed.
•
Release the switch and ENGINE 8 will be displayed.
•
Tap SW1 (I) until ENGINE BUS is displayed.
•
Press and hold SW1 (I) until DONE is displayed.
•
Tap SW1 (I) until TACH DONE is displayed.
•
Press and hold SW1 (I) until a big DONE is displayed.
Obtaining engine temperature from the BIM-01-2-FTCH
•
Hold the SW1 (I) switch from the instrument system control box while turning the key on.
o
The message display should show SETUP.
•
Release SW1 (I) - LCD1 should show SETUP SPEED.
•
Tap SW1 (I) until SETUP WATER is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until WATER SENDER is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until SENDER DD F is displayed.
•
Release the switch and SENDER DD F will be displayed.
•
Tap SW1 (I) until SENDER BUS F (Fahrenheit) is displayed.
o
Tap SW1 (I) once more for SENDER BUS C (Celsius) if desired.
•
Press and hold SW1 until DONE is displayed.
•
Tap SW1 (I) until WATER DONE is displayed.
•
Press and hold SW1 (I) until a big DONE is displayed.
***Intake/manifold air temp, air fuel ratio, trans fluid temp, and boost will be displayed in the message center if activated through the display menu setup.
(N/A on TBI system)
Drive a known speed and calculate how far off the speed is in percentage.
•
GPS speed / displayed speed x 100
•
Sample - [60/50=1.2] [1.2x100 = 120] 120%
Enter setup and go to ADJUST, tap SW1 (I) to increment from 100% up to 125%.
After 125% the values will fall back to 75% and increment up again.
When the desired percentage is reached, hold SW1 (I) until DONE is displayed
[4]
MAN #650819A
Advertisement
