Page 2
Hewlett Packard Enterprise Company. To obtain such source code, please check if the code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software...
Preface This document describes the hardware features of the HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway. It provides a detailed overview of the physical and performance characteristics of the Gateway and explains how to install the Gateway and its accessories.
Chapter 1 Gateway Components The HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway provides high-performance networking and SD-WAN in compact and cost-effective form factor, ideally suited for small branch and remote office environments. Table 2 describes the Gateway ports and their configuration.
Wall mount kit (2 screws, 2 anchors) Power cord retainer clip Component Descriptions Optional accessories are available for use with the HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway and are sold separately. Contact your HPE Aruba Networking sales representative for details and assistance.
Page 7
LINK/ACT: Placed on the left side of the port; displays the link status and activity of the port. STATUS: Placed on the right side of the port; displays the speed of the port. HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Gateway Components |...
Page 8
Link status Green (Solid) Link established Green (Blinking) Port is transmitting or receiving data No link STATUS Port status Speed Green (Solid) Link at 1000 Mbps No link HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Gateway Components |...
Page 9
Green (Blinking) Port is transmitting or receiving data No link STATUS Port status Speed Green (Solid) Link at 10 Gbps Amber (Solid) Link at 1000 Mbps No link HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Gateway Components |...
Page 10
RJ-45 console connection. USB Type C Driver To use the USB console port, you must install the HPE Aruba Networking USB driver on the computer that will manage your SD-WAN. To download the driver, perform the following steps: 1.
Page 11
The EdgeConnect 10106 SD-WAN Gateway is equipped with a USB 3.0 interface. A USB storage device can be used to save and upload configurations to the Gateway. HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Gateway Components |...
can over heat the Gateway. Precautions Dangerous voltage above 240 V AC is always present while an HPE Aruba Networking gateway is plugged into an electrical outlet. Remove all rings, jewelry, and other potentially conductive material before working with this device.
Installation Steps 1. Remove the grounding screw from the rear panel. Figure 10 Removing the Grounding Screw from the Rear Panel 5 4 V 2 .5 0 A HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
Page 14
Figure 12 Attaching the Power Tray to the Gateway 4. Attach the grounding cable to the rear panel using the grounding screw removed in step 1. Figure 13 Attaching the Grounding Cable 54 V 3. 34 A HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
Page 15
Figure 14 Installing the Power Adapter Figure 15 Power Adapter Installed into Tray 6. Connect the power cable with DC jack after winding the cable neatly. Figure 16 Attaching the Power Cord HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
Page 16
9. Attach the AC cord and the cord clip to the tray. Figure 18 Attaching the AC cord and cord clip Figure 19 AC Power Cord is Attached HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
Page 17
Leave a minimum of 10 cm (4 inches) of space on the left and right side of the device for proper air flow and ventilation. Leave additional space in the front and the back of the device to access network cables, LED status indicators, and power cord. HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
1. Attach the rubber feet to the bottom of the Gateway. See Figure Figure 21 Attaching Rubber Feet to the Gateway Figure 22 Rubber Feet Attached to the Gateway 2. Place the Gateway in the location you have chosen. HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
4. Create the holes and insert wall anchors if your installation requires them. 5. Align the mounting bracket holes with the holes you created on the wall. See Figure HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
Page 20
6. Use appropriate screws to secure the Gateway. Figure 24 Wall Mounting HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Installation |...
Chapter 3 Configuring the Gateway IMPORTANT - READ THIS FIRST: You must install and register your Orchestrator with the HPE Aruba Networking Cloud Portal BEFORE setting up an EdgeConnect gateway. After Orchestrator is registered with your account name and key, you can proceed with EdgeConnect installation. If you don’t know or are unsure about Orchestrator’s role, contact your network architect or deployment lead.
Turn the Power On The Gateway powers up as soon as it is plugged into the local power source. On the front panel, verify the Power LED illuminates green. HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Configuring the Gateway |...
3. Complete the remaining wizard screens. On the Deployment page’s default configuration, the WAN–side interfaces use DHCP IP addresses, unless you manually enter static IP addresses. HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Configuring the Gateway |...
This document can be viewed or downloaded from the following location: www.arubanetworks.com/ safety_addendum HPE Aruba Networking gateways must be installed by a professional installer. The professional installer is responsible for ensuring that grounding is available and meets applicable local and national electrical codes. HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway...
Page 25
2. This device must accept any interference received, including interference that may cause unde- sired operation. Changes or modifications to this unit not expressly approved by HPE Aruba Networking could void the user’s authority to operate this equipment. Industry Canada This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations.
Page 26
China RoHS material content declaration HPE Aruba Networking EdgeConnect 10106 SD-WAN Gateway | Installation Guide Specifications, Safety, and Compliance |...
Page 27
EU Regulatory Conformance The Declaration of Conformity made under EMC Directive 2014/30/EU is available for viewing at http://www.hpe.com/eu/certificates. Select the document that corresponds to your device’s model number as it is indicated on the product label. Use of controls or adjustments of performance or procedures other than those specified in this manual may result in hazardous radiation exposure.
Proper Disposal of HPE Aruba Networking Equipment Waste of Electrical and Electronic Equipment HPE Aruba Networking products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment...