Related Manuals for Body Solid GLM85B
Summary of Contents for Body Solid GLM85B
- Page 1 GLM85B & A s s e m b l y I n s t r u c t i o n s O W N E R ’ S M A N U A L V. GLM85B-20240123...
- Page 2 W a r n i n g , S a f e t y & M a i n t e n a n c e ...
-
Page 3: Table Of Contents
T a b l e o f C o n t e n t s • SAFETY INSTRUCTIONS......PAGE 4 • PREPARATION..........PAGE 5 • HARDWARE ILLUSTRATION......PAGE 6 • PART / HARDWARE LIST....... PAGE 10 • ASSEMBLY INSTRUCTIONS......PAGE 12 • EXPLODED VIEW.......... -
Page 4: Safety Instructions
Before beginning assembly, please take the time that we can assist you better. to read the instructions thoroughly. 1. Model Number m Read each step in the assembly instructions and 2. Place of Purchase follow the steps in sequence. Do not skip ahead. 3. Serial Number (S/N) If you skip ahead, you may learn later that you 4. Part # and Description have to disassemble components and that you may have damaged the equipment. m Assemble and operate the GLM85B on a solid, level surface. Locate the unit a few feet from the walls or furniture to provide easy access. -
Page 5: Preparation
P r e p a r a t i o n Thank you for purchasing the GLM85B. This Product is part of the Body-Solid line of quality strength training machines, which lets you target specific muscle groups to achieve better muscle tone and overall body conditioning. To maximize your use of the equipment please study this Owner’s Manual thoroughly. Required Tools Assembly Tips The basic tools that you must obtain before assembling Read all “Notes” on each page before beginning each the GLM85B include but are not limited to: step. While you may be able to assemble the GLM85B using the illustrations only, important safety notes and other m Standard Wrench Set tips are included in the text. -
Page 6: Hardware Illustration
G L M 8 5 B H a r d w a r e I l l u s t r a t i o n Part #1 M10x100mm HEX HEAD BOLT QTY. - Page 7 G L M 8 5 B H a r d w a r e I l l u s t r a t i o n Part #5 M10x45mm HEX HEAD BOLT QTY.
- Page 8 G L M 8 5 B H a r d w a r e I l l u s t r a t i o n Part #9 M8x8mm SET SCREW QTY.
- Page 9 G L M 8 5 B H a r d w a r e I l l u s t r a t i o n Part #13 M10 LOCK WASHER QTY.
-
Page 10: Part / Hardware List
G L M 8 5 B P a r t s & H a r d w a r e L i s t Part# Description FRONT BASE FRAME REAR BASE FRAME UPRIGHT SEAT FRAME TOP FRAME GUIDE ROD LAT BAR KNEE HOLD DOWN FRAME FOOT PLATE FOAM ROLLER BAR... - Page 11 G L M 8 5 B P a r t s & H a r d w a r e L i s t Part# Description LOW ROW BAR FOAM GRIP SNAP LINK STEEL CHAIN (10 PCS) TOP CABLE, 2530mm SHAFT, ø18.5x401mm PLASTIC BUSHING, 60x60x47mm POP PIN SEAT PAD PLASTIC END CAP, ø95mm FOAM ROLLER, ø100x200mm PLASTIC RING, ø75xø25.5x3mm...
-
Page 12: Assembly Instructions
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware in this step. DO NOT wrench tighten until instructed. Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tightened to fully go on. - Page 13 S T E P Above shows Step 1 assembled and completed.
- Page 14 S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware in this step. DO NOT wrench tighten until instructed. Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tightened to fully go on.
- Page 15 S T E P Above shows Step 2 (Option#1) assembled and Above shows Step 2 (Option#2) assembled and completed. completed.
- Page 16 S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Wrench tighten ALL hardware at the end of STEP 3E. Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tighten to fully go on.
- Page 17 S T E P Above shows Step 3 assembled and completed.
- Page 18 S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Wrench tighten ALL hardware at the end of STEP 4F. Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tighten to fully go on.
- Page 19 S T E P Above shows Step 4 assembled and completed.
- Page 20 S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Wrench tighten ALL hardware at the end of STEP 5G. Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tighten to fully go on.
- Page 21 S T E P Above shows Step 5 assembled and completed.
- Page 22 S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tightened to fully go on. 6A. Attach Lat Bar (G) to the Top Cable (#24).
- Page 23 S T E P Above shows Step 6 assembled and completed.
- Page 24 N o t e s...
-
Page 25: Exploded View
G L M 8 5 B E x p l o d e d V i e w... -
Page 26: Contact Page
GLM85B PLEASE WRITE YOUR SERIAL NUMBER IN THE BOXES BELOW 014664-��-��-����-���� S/N # 1900 S. Des Plaines Ave. Forest Park, IL 60130 Phone:(708)427-3555 Fax:(708)427-3556 Hours: M-F 8:30 - 5:00 CST www.bodysolid.com Copyright 2009. Body-Solid. All rights reserved. Body-Solid reserves the right to change design and specifications when we feel it will improve the product.