Carrier Aero 39MN MW03-110 Series Installation, Start-Up And Service Instructions Manual page 55

39M UNIT SIZE
CIRCUITING TYPE
Airflow (cfm) at 500 fpm
Total Face Area (sq ft)
Tubes in Face
Tube Length (in.)
No. of Circuits - Total
4-Row Coil
Face Split Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
Intertwined Row Split Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
Single Circuit Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
6-Row Coil
Face Split Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
Intertwined Row Split Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
Single Circuit Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
8-Row Coil
Face Split Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
Intertwined Row Split Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
Single Circuit Coils
No. of TXVs
Suction Connections (in. OD)
Distributor Connections (in. OD)
Distributor Nozzle Size
LEGEND
TXV — Thermostatic Expansion Valve (Field Supplied)
*When 2 nozzle sizes are listed, the smaller nozzle should be located on the upper distributor.
NOTE: Factory-supplied distributors have factory-selected nozzle sizes as shown. If necessary,
replace factory-supplied nozzles with field-supplied and installed nozzles. Consult
AHUBuilder ® software selection program for correct nozzle selection.
Table 11 — Direct-Expansion Circuiting Data (cont)
Large Face Area Coils (cont)
14W
Quarter Half Full Quarter
7,170
14.3
28 28 28 22
59 59 59 38
7 14 28 6
Upper
2 2 2 2
7/8 1-1/8 1-5/8 7/8
7/8 7/8 1-3/8 7/8
G-2.5/G-2 G-6 C-15 G-2
2 2 2 2
7/8 1-1/8 1-5/8 7/8
7/8 7/8 1-3/8 7/8
G-2.5/G-2 G-6 C-15 G-2
1 1 — 1
1-1/8 1-5/8 — 1-1/8
7/8 1-3/8 — 7/8
G-6 C-15 — G-4
— 2 2 —
— 1-1/8 1-5/8 —
— 7/8 1-3/8 —
— G-6 C-15 —
— 2 2 —
— 1-1/8 1-5/8 —
— 7/8 1-3/8 —
— G-6 C-15 —
— 1 — —
— 1-5/8 — —
— 1-3/8 — —
— C-15 — —
— 2 2 —
— 1-1/8 1-5/8 —
— 7/8 1-3/8 —
— G-6 C-15 —
— 2 2 —
— 1-1/8 1-5/8 —
— 7/8 1-3/8 —
— G-6 C-15 —
— 1 — —
— 1-5/8 — —
— 1-3/8 — —
— C-15 — —
16T
Half Full
7,587
15.2
24 22 24 22
38 38 38 38
6 11 12 22
Lower Upper Lower Upper
2 2 2 2
7/8 1-1/8 1-1/8 1-3/8
7/8 7/8 7/8 1-1/8
G-2 G-4/G-3 G-4 E-12
2 2 2 2
7/8 1-1/8 1-1/8 1-3/8
7/8 7/8 7/8 1-1/8
G-2 G-4/G-3 G-4 E-12
1 1 1 —
1-1/8 1-3/8 1-3/8 —
7/8 1-1/8 1-3/8 —
G-4 E-12 C-12 —
— 2 2 2
— 1-1/8 1-1/8 1-3/8
— 7/8 7/8 1-1/8
— G-4 / G-3 G-4 E-12
— 2 2 2
— 1-1/8 1-1/8 1-3/8
— 7/8 7/8 1-1/8
— G-4 / G-3 G-4 E-12
— 1 1 —
— 1-3/8 1-3/8 —
— 1-1/8 1-3/8 —
— E-12 C-12 —
— 2 2 2
— 1-1/8 1-1/8 1-3/8
— 7/8 7/8 1-1/8
— G-4 / G-3 G-4 E-12
— 2 2 2
— 1-1/8 1-1/8 1-3/8
— 7/8 7/8 1-1/8
— G-4 / G-3 G-4 E-12
— — — —
— — — —
— — — —
— — — —
55
Double Half
24 22 24 30
38 38 38 65
24 44 48 15
Lower Upper Lower
2 — — 2
1-3/8 — — 1-1/8
1-3/8 — — 7/8
C-12 — — G-8/G-6
2 — — 2
1-3/8 — — 1-1/8
1-3/8 — — 7/8
C-12 — — G-8/G-6
— — — 1
— — — 1-5/8
— — — 1-3/8
— — — C-15
2 — — 2
1-3/8 — — 1-1/8
1-3/8 — — 7/8
C-12 — — G-8 / G-6
2 — — 2
1-3/8 — — 1-1/8
1-3/8 — — 7/8
C-12 — — G-8 / G-6
— — — 1
— — — 1-5/8
— — — 1-3/8
— — — C-15
2 4 4 2
1-3/8 1-3/8 1-3/8 1-1/8
1-3/8 1-1/8 1-3/8 7/8
C-12 E-12 C-12 G-8 / G-6
2 4 4 2
1-3/8 1-3/8 1-3/8 1-1/8
1-3/8 1-1/8 1-3/8 7/8
C-12 E-12 C-12 G-8 / G-6
— — — 1
— — — 1-5/8
— — — 1-3/8
— — — C-15
17W
Full Double
8,464
16.9
30 30
65 65
30 60
2 —
1-5/8 —
1-3/8 —
C-15 —
2 —
1-5/8 —
1-3/8 —
C-15 —
— —
— —
— —
— —
2 —
1-5/8 —
1-3/8 —
C-15 —
2 —
1-5/8 —
1-3/8 —
C-15 —
— —
— —
— —
— —
2 4
1-5/8 1-5/8
1-3/8 1-3/8
C-15 C-15
2 4
1-5/8 1-5/8
1-3/8 1-3/8
C-15 C-15
— —
— —
— —
— —