Carrier 36S Installation Instructions Manual
Carrier 36S Installation Instructions Manual

Carrier 36S Installation Instructions Manual

Induction air terminals
Hide thumbs Also See for 36S:

Advertisement

Quick Links

CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
VERTICAL UNIT INSTALLATION . . . . . . . . . . . . . . . . 2
Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Step 2 - Make Air Connections . . . . . . . . . . . . . . . . 2
Step 3 - Connect Piping . . . . . . . . . . . . . . . . . . . . . 3
Step 5 - Install Carrier Enclosures . . . . . . . . . . . . . 3
Runouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
as Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 8 - Balance System . . . . . . . . . . . . . . . . . . . . 7
Wall-Mounted Thermostat) . . . . . . . . . . . . . . . . . . 7
BASE UNIT IN CARRIER ENCLOSURE . . . . . . . . . . . 7
COIL REVERSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GENERAL

These units are controlled by varying water flow through coil. Fol-
low installation steps in sequence suggested. Each step includes
figure(s) and procedures required for a specific stage of
installation.
Set up a sample installation to familiarize all trades with their spe-
cific job function.
See Fig. 1 for the Proposition 65 warning label. See Fig. 2 and 3
for 36SV,SL base units.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53360010-01
Installation Instructions
Printed in U.S.A.
Form No. 36S-2SI
Induction Air Terminals
(Bypass and Water Control)
WARNING
!
This product can expose you to chemicals
including Acrylonitrile, which is known to the
State of California to cause cancer. For
more information, go to
www.P65Warnings.ca.gov
AVERTISSEMENT
!
Ce produit peut vous exposer à des
agents chimiques, y compris l'acrylonitrile,
que l'État de Californie reconnaît comme
cancérigènes. Pour plus d'informations,
veuillez consulter
www.P65Warnings.ca.gov
ADVERTENCIA
!
Este producto puede exponerlo a productos
químicos que incluyen acrilonitrilo, que
el estado de California considera que
causa cáncer. Para más información visite
www.P65Warnings.ca.gov
Fig. 1 - Proposition 65 Warning Label
Return
Supply
Condensate
Pan
Fig. 2 - 36SV Base Unit
Pg 1
36S
Primary Air Inlet
5-24
Replaces: 36S-1SI

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 36S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Carrier 36S

  • Page 1: Table Of Contents

    Step 4 — Install Accessory Grilles (If Supplied, on Furred-In or Custom Enclosure Installations) . . 3 Step 5 — Install Carrier Enclosures ... . . 3 AVERTISSEMENT Step 6 — Install Stiffener Brackets for Enclosure Runouts .
  • Page 2: Vertical Unit Installation

    Base Unit Determine required length of mounting strip. Allow for length of enclosures and runouts to be used. Maximum unsupported length of Carrier enclosures is 2 in. on either side. Locate strip per job prints. Install straight and level using field-supplied fasteners through alternate and end holes.
  • Page 3: Step 3 - Connect Piping

    Fig. 7 — Accessory Grilles and Field-Supplied Collar Level condensate pan; straighten strap. If drainable con- densate pan in used, connect to drain line. Pitch drain line Step 5 — Install Carrier Enclosures for adequate flow. Remove enclosures from carton.
  • Page 4: Step 6 - Install Stiffener Brackets For Enclosure

    Step 6 — Install Stiffener Brackets for Enclosure Step 7 — Install Enclosure and Runout Arrange- Runouts ment as Required Determine length of runout from job prints. Use end frame as template when drilling holes on unit enclosure side panels. Tap runout enclosure lightly to ensure tight fit in end Place stiffener brackets on wall mounting strip.
  • Page 5: Column-To-Column With Shelving

    COLUMN-TO-COLUMN WITH SHELVING Insert shelving below end panels, with flanges turned down. Shelving rests on lower flange of end frame. Drill two 3/16 in. holes for attaching runout. See Fig. 11. Hang assembly on wall mounting strip and adjacent to unit Cut runout enclosure, back panel, and shelving to desired enclosure.
  • Page 6: Enclosure With Single Or Dual Runout

    ENCLOSURE WITH SINGLE OR DUAL RUNOUT SINGLE OR DUAL RUNOUT WITH KICKSTRIP Drill two 3/16 in. holes for attaching runout. See Fig. 12. Drill one 3/16 in. hole for attaching runout. See Fig. 13. Cut runout enclosure to desired length; fit into slots of 2 Cut runout enclosure and kickstrip to desired length;...
  • Page 7: Step 8 - Balance System

    Use 2 screws and clips taped to unit front (Unit-Mounted or Wall-Mounted Thermostat) panel. Install one screw on either side of coil support and Base Unit Not in Carrier Enclosure below screen. Install clips through hole as shown. Remove unit from carton. Remove protective packing. .
  • Page 8: Coil Reversal

    Flanges Fasten to Mounting Plate Flange Fig. 16 — 36SH Installed in Carrier Enclosure © 2024 Carrier Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Catalog No. 04-53360010-01 Printed in U.S.A.

Table of Contents