Cleaning And Care - Vitek VT-1185 Manual Instruction

ENGLISH
– The unit can maintain the water temperature for
an unlimited period of time. As long as it is con-
nected to a power source, the water will remain
warm.
– If the cooling mode is selected, the keep warm
mode is deactivated and the cooling or power
off indicator «OFF | ВЫКЛ» (17) appears. The
water will gradually cool down to room tem-
perature.
Re-boiling function
You can reboil cooled water. Press the «REBOIL | По-
вторное кипячение» reboiling button (27).
The boiling indicator (21) will light up. After the boil-
ing process is finished, the indicator (21) will go out
and the keep warm indicator (22) will light up.
Reboiling will not start if the water level in the ther-
mopot is low.
Water dispensing
•
Put a suitable bowl under the spout (9).
•
Press the button (28) to unlock the water sup-
ply, while the lock indicator (19) on the display
(23) will go out.
•
Press and hold the «DISPENSE | Налить» water
dispense button (8) to fill the bowl. Hot water will
pour from the spout (9) into the bowl as long as
the water dispense button (8) is pressed.
Note: if, after unlocking, no action is taken for
about 8 seconds, the water dispense lock will be
switched on automatically and the indicator (19)
will light up on the display.
Attention! Be careful when pouring out water to
avoid burns by hot water.
Boiling
•
Select the desired temperature with the
«T°C SET | Выбор T°C» water heating tem-
perature selection button (26), press the
«REBOIL | Повторное кипячение» reboiling
button (27).
•
After that, the boiling function will start, which
will be displayed on the control panel (7) by the
indicator (21).
•
After long water boiling is finished, the thermo-
pot will switch to the keep warm mode at 85 °C,
the indicator (21) will go out and the corre-
sponding temperature mode indicator (22) will
light up.
•
If the water temperature drops significantly
below the set one, for example, if you added
cold water, the boiling mode will switch on, the
indicator (21) will glow constantly. After boil-
ing water, its temperature will be maintained
depending on the set value of the indicator
(23). When the temperature drops below the set
value, the indicator will start flashing.
•
To disconnect the thermopot from the mains,
disconnect the power plug (16) from the mains
socket.
•
Open the thermopot lid (1) and wait until it cools
down completely, remove the lid (1) (see the
chapters Before the first use and Cleaning
and care), drain the water, install the lid (1)
back to its place and put the thermopot away
for storage.
Attention! Be careful when pouring out water to
avoid burns by hot water.
Overheat protection
If you accidentally switch the thermopot on without
water, the automatic thermal switch will work, and
the indications will completely disappear from the
panel (7).
In this case unplug the thermopot and let it cool
down for 10-20 minutes, then fill it with water, and
switch the thermopot on, the unit will operate in
normal mode.

CLEANING AND CARE

•
Before cleaning, disconnect the thermopot from
the mains, pour out water and let the thermopot
cool down completely.
•
Open the lid (1) and then remove it.
Removing the lid
To remove the lid (1), perform the steps shown on
the pictures 1, 2 and 3:
•
Open the lid (pic. 1).
•
Lift the lid at an angle of about 30-40 degrees,
pull it forward (towards the panel (7) and remove
the lid) (pic. 2).
•
Carefully drain the remaining water, make
sure that the water does not get on the control
panel (7).
•
Insert the lid (1) back at the angle (pic. 3), then
close the lid (1).
•
Clean the outer surface of the thermopot with a
slightly damp cloth and then wipe it dry.
•
Use neutral detergents to remove dirt; do not
use metal brushes, abrasive detergents and
solvents.
•
Do not immerse the thermopot and the power
cord into water and other liquids.
•
Do not wash the thermopot in a dishwashing
machine.
12