Cleaning And Care - Vitek VT-1186 Manual Instruction

ENGLISH
Option 1: Place a suitable container under the wa-
ter outlet nozzle (4), such as a cup, and press the
dispensing button (3) with the edge of the cup.
Option 2: Place a suitable container under the wa-
ter outlet nozzle (4) and press the «DISPENSE» but-
ton (24) to dispense water.
Note: - water dispensing occurs only when the
indicator (20) « » is lit. If no action is taken after
pressing the button (21), the indicator (20) « » will
turn off after 10 seconds.
•
Unplug the power cord plug (25) from the mains
to switch the thermo pot off.
•
Open the thermo pot lid (8) and wait for it to
cool down completely. Remove the lid (8) (see
«BEFORE THE FIRST USE» section), drain the
water, place the lid (8) back on, and store the
thermo pot.
•
Open the thermopot lid (8) and wait until it cools
down completely, remove the lid (8) (see the
chapter BEFORE THE FIRST USE), drain the
water, install the lid (8) back to its place and put
the thermopot away for storage.
TIMER SETTING FOR THE THERMO POT
•
To activate the timer, press the «TIMER» button
(15). The «TIMER» indicator (14) will turn on, and
the digital display (23) will show the time until the
thermo pot turns on, such as «2H».
•
By tapping the «TIMER» button (15), you can
set the thermo pot to turn on in from 2 to 24
hours. The selected time will be shown on the
display (23). To deactivate the timer, press the
«TIMER» button (15) until the indicator (14)
turns off, or unplug the power cord plug (25)
from the mains.
Overheat protection
•
If the thermo pot is accidentally switched on
with the water level below the minimum mark,
the automatic thermal cutoff will activate, and
«E2, E1» symbols will appear on the display
(23). In this case, unplug the power cord plug
from the mains, allow the thermo pot to cool for
20-30 minutes, refill it with water, and switch it
on. The thermo pot will operate normally.

CLEANING AND CARE

•
Before cleaning, disconnect the thermopot from
the mains, pour out water and let the thermopot
cool down completely.
•
Before removing the lid (8) open it and pull the
lid (8) to the control panel (5).
•
Carefully tilt the thermopot to drain the remain-
ing water.
•
Install the lid (8) in the lock (9). To do it, place the
lid (8) at a small angle and insert the lid (8) into
the lock (9). Before using the thermopot make
sure that the lid (8) is fixed properly.
•
Clean the exterior surface of the thermo pot
body (11) with a slightly damp cloth, then wipe
it dry.
•
Use neutral cleaning agents for removing stains.
Do not use metal brushes, abrasive cleaning
agents, or solvents.
•
Do not submerge the power cord (25) or thermo
pot in water or any other liquids.
•
Do not wash the thermopot in a dishwashing
machine.
Stains on the inner surface of the thermopot
The inner surface of the metal flask may change
its color under the influence of different water
impurities.
•
You can remove the stains with citric acid or vin-
egar.
•
To remove the flavour of citric acid or vinegar,
boil water and pour it out.
•
Repeat this procedure until the smell and taste
vanish completely.
Descaling
•
Scale, appearing inside the metal flask, causes
the heating element overheating and malfunc-
tion. Burning of the heating element caused
by the scale in the thermopot is not covered by
warranty.
•
To remove scale, fill the thermo pot with water
mixed with white vinegar in a 2:1 ratio up to the
«FULL» level mark.
•
Insert the power cord plug (25) into the socket
(12) on the thermo pot body, and plug the power
cord (25) into the mains.
•
The thermo pot will enter boiling mode. After
the water boils, unplug the power cord plug (25)
from the mains and leave the thermo pot with the
vinegar solution overnight.
•
In the morning pour out the vinegar solution, fill
the thermopot with water up to the maximal level
«FULL», boil it and pour out the water.
12