Vitek VT-1185 Manual Instruction page 11

will hear a sound signal, and all indicators will
light up on the display for a short time.
•
Boiling process will switch on automatically.
The unit will automatically switch to the heating
mode and start heating water up to the default
keep warm temperature of 85 °C. The indicators
for boiling water (21), the power on icon (18) and
the set temperature of 85 °C will light up.
•
After long water boiling is finished, the thermo-
pot will switch to the keep warm mode at 85 °C.
Note: the thermopot uses a long boiling technol-
ogy which allows to significantly reduce the chlo-
rine level in water.
•
Drain the water; to do this, unlock the activation
of the water pump by pressing the button (28),
the lock indicator (19) on the control panel (7)
will go out.
Note: If, after unlocking, no action is taken for 8 sec-
onds, the lock will be switched on again automatically
and the locking indicator (19) will light up again.
Attention! Do not open the lid immediately after
the water has finished heating - risk of burns from
hot steam!
Attention! Be careful when pouring out water to
avoid burns by hot water.
To drain the water from the thermopot
– Place a suitable bowl under the water dis-
pense spout (9), for instance, a cup, press the
«UNLOCK | Разблокировка» button (28), the
lock indicator (19) will go out, then press the
«DISPENSE | Налить» (8) water dispense but-
ton and hold it until the bowl is filled to desired
level.
– Hot water will dispense from the spout (9).
– Release the «DISPENSE | Налить» button, and
the water dispensing will stop.
•
To switch the thermopot off disconnect the
power plug (16) from the mains socket.
•
Wait until the water cools down to room tem-
perature.
•
Open the thermopot lid (1) and wait until it cools
down completely.
•
Remove the lid (1) (see the chapter «Cleaning
and care»).
•
Carefully tilt the thermopot to drain the remain-
ing water. Make sure that water does not get on
the control panel.
•
Install the lid (1) back to its place (see the chap-
ter «Cleaning and care»). Before using the
thermopot make sure that the lid (1) is fixed
properly.
•
The thermopot is ready to use.
USING THE THERMOPOT
•
Open the lid (1) by pressing the lid opening but-
ton (2), take the lid (1) and pull upwards.
•
Fill the thermopot with clean water using a suit-
able bowl, do not exceed the «FULL» maximal
water level mark (6) on the inner side of the
water tank (10). Do not pour water above the
«FULL» mark (6), as hot water may splash out
when boiled.
•
Insert the power cord (16) connector into the
socket (15) on the thermopot body, and the
power cord (16) plug into the mains socket. The
process of slow boiling will start, the display (24)
will show the heating (21), «ON | ВКЛ» power
(18) and lock (19) indicators.
•
When the temperature reaches 100 °C, the
thermopot will automatically switch to the tem-
perature maintenance mode at 85 °C. The tem-
perature maintaining mode indicator (22) will
light up on the panel (7).
Note:
– Do not open the upper lid during water boiling.
– Do not add water when it's boiling.
– Do not block the steam release opening (3) of
the upper lid (1).
– The thermopot will maintain the temperature at
85 °С by default.
Temperature selection
To change the required temperature for main-
taining hot water, consequently press the «T°C
SET | Выбор T°C» heating temperature selec-
tion button (26). The temperature selection in-
dicators will sequentially change in the range
95/85/75/65/55/45 (23) or switching the wa-
ter heating off «OFF | ВЫКЛ» (17), which cor-
responds to the water heating temperature
«95°C/85°C/75°C/65°C/55°C/45°C» or the activa-
tion of the water cooling mode.
Notes:
– If the selected temperature is lower than the
temperature in the thermopot, then the water in
the thermopot will first cool down to the set tem-
perature, after which the selected temperature
will be maintained. When the water temperature
in the thermopot drops below the set tempera-
ture by more than 5 degrees, the thermopot will
switch to heating mode.
– The selected temperature value indicator will
flash as long as the water remains at the keep
warm temperature. When the set temperature
is reached, the temperature indicator will stop
flashing.
11
ENGLISH