Vitek VT-1185 Manual Instruction page 10

ENGLISH
•
Do not apply excessive effort when closing the
lid. When using the thermopot, make sure that
the lid is closed tightly.
•
Keep your hands away and do not bend over the
steam release openings, it may cause burns.
Do not block the steam release opening with
any objects.
•
Do not touch hot surfaces of the thermopot.
•
Be careful while carrying the thermopot filled
with boiling water.
•
Provide that no water gets on the display or
touch buttons.
•
Be careful, avoid getting liquid on the electric
connectors during cleaning or filling the thermo-
pot with water and pouring the water out.
•
Do not carry the thermopot holding it by the lid
opening button.
•
Be careful when pouring out hot water.
•
Be careful, the heating element surface remains
hot for some time after the use!
•
To avoid risk of electric shock, do not immerse
the thermopot, the power cord and the power
plug of the unit into water or other liquids.
•
Unplug the unit, if you are not using it or before
cleaning.
•
Do not wash the thermopot in a dishwashing
machine.
•
Before taking the unit away for long storage or
before cleaning, unplug it, pour out water and
let the unit cool down and dry.
•
For child safety reasons do not leave polyethyl-
ene bags used as packaging unattended.
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger of
suffocation!
•
Close supervision is necessary when children
or disabled persons are near the operating unit.
•
This unit is not intended for usage by children.
•
Place the unit out of reach of children during
operation and cooling down.
•
Do not allow children to touch the unit body or
the power cord during operation.
•
The unit is not intended to be used by peo-
ple with physical, sensory or mental disabilities
(including children) or by persons lacking expe-
rience or knowledge if they are not under the
supervision of a person who is responsible for
their safety or if they are not instructed by this
person on the usage of the unit.
•
Do not leave children unattended to avoid them
using the unit as a toy.
•
Check the integrity of the power cord, the power
plug and the thermopot body periodically.
•
Never use the unit if the power cord or the power
cord plug is damaged, if the unit works improp-
erly or after it was dropped.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
•
Do not repair the unit by yourself. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. COMMERCIAL USAGE AND USAGE IN
PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After the unit transportation or storage at low
temperature keep it for at least three hours at
room temperature before switching on.
There may be water spots in the thermopot, this is
normal, as the unit has undergone factory quality
control.
•
Unpack the thermopot; remove any advertis-
ing stickers that can prevent the unit operation.
•
Check the unit for damages, do not use it in case
of damages.
•
Make sure that the unit operating voltage corre-
sponds to the voltage of your mains.
•
Place the thermopot on a dry flat surface keep-
ing at least 20 cm gap between the thermopot
body and the wall or furniture and at least 50 cm
gap above the thermopot.
•
Open the lid (1) by pressing the button (2), hold
it and lift upwards.
•
Fill the thermopot with water using a suitable
container, make sure that the water level is
above the «MIN» mark (14) and does not exceed
the «FULL» maximal water level mark (6) located
on the inside of the thermopot water tank (10).
•
Close the lid by pressing on it until clicking.
Make sure that the lid is closed tightly.
Note: If the lid is not closed tightly, the water will not
heat up to the required temperature.
•
Insert the power cord (16) connector into the
socket (15) on the thermopot body, and the
power cord (16) plug into the mains socket. You
10