Advertisement
Available languages
Available languages
The defrosting procedure consists of three stages:
•
Defrosting stage: Parameter d3 establishes the
maximum duration of the stage.
Output status:
-
The compressor is active if d1 = 1,otherwise it is
switched off;
-
The defrosting relay is active if d1 = 0 or d1 =
1,otherwise it is switched off;
-
The fans are switched on if d1 = 2, otherwise
they are switched off.
•
Dripping
stage:
Parameter d7
duration of the stage.
Output status:
-
The compressor is switched off;
-
The defrosting relay is active if d1 = 0 or d1
= 1,otherwise it is switched off; -
The fans are switched off.
•
Drying stage.
Parameter d16 establishes the duration of the stage.
Output status:
-
The compressor acts according to parameter d8;
-
The defrosting relay is active if d1 = 0 or d1
= 1,otherwise it is switched off; -
The fans are switched off.
If the "Anti-Legionella" or the "Overboost"
functions are in progress, the defrosting
procedure will not be enabled.
7.1.3.14 Day and real time settings
•
Make sure that the keyboard is not locked
(paragraph 7.1.3.3) and that no other advanced
procedure is in progress;
•
Press and release the
show the first code available;
•
Press and release either the
until "rtc" is shown;
The day is displayed as 1...7 (number 1 corresponding to
Monday). To change the day of the week:
•
Press and release the
show "dd" followed by the two numbers representing
the day;
•
Press and release either the
within 15 seconds.
To change the time:
•
Press and release the
the day of the month: the display will show "hh"
followed by the two numbers representing the time
(Time is shown in the 24 hr. format);
•
Press and release either the
within 15 seconds.
To change the minutes:
•
Press and release the
the time: the display will show "nn" followed by the
two numbers representing the minutes;
•
Press and release either the
within 15 seconds;
•
Press and release the
out any operations for 15 seconds; To exit the
procedure:
•
Press and release the
shows the temperature established by parameter P5
or do not carry out any operations for 60 seconds.
Alternatively:
•
Press and release the
establishes
the
key: the display will
or the
key
key: the display will
or the
key
key while changing
or the
key
key while changing
or the
key
key or do not carry
key until the display
key.
To
set
operations
necessary to have carried out the settings
relating to the day and the real time before-
hand.
7.1.3.15 Configuration parameter settings
To carry out the procedure:
•
Make sure that the keyboard is not locked
(paragraph 7.1.3.3) and that no other advanced
procedure is in progress;
•
Keep the
seconds: the display will show "PA" (password); •
Press and release the
•
Press and release either the
within 15 seconds to set "-19" on the display;
•
Press and release the
out any other operations for 15 seconds;
•
Keep the
seconds: the display will show the first parameter
"SP1".
To select a parameter:
•
Press and release either the
To change a parameter:
•
Press and release the
•
Press either the
increase or reduce the parameter value (within 15
seconds);
•
Press and release the
out any operations for 15 seconds.
To exit the procedure:
•
Keep the
seconds or do not carry out any operations for 60
seconds (any changes will be saved).
Switch the equipment off and then back on
again to make the changes made to
parameters effective.
7.1.3.16 Restoring default factory settings
To carry out the procedure:
•
Ensure
that
(paragraph 7.1.3.3) and that no other advanced
procedure is in progress;
•
Keep the
seconds: the display will show "PA" (password); •
Press and release the
•
Press and release either the
within 15 seconds to set "149";
•
Press and release the
out any operations for 15 seconds;
•
Keep the
seconds: the display will show "dEF";
•
Press and release the
•
Press and release either the
within 15 seconds to set "1";
•
Press and release the
out any other operations for 15 seconds: the display
will show "dEF" flashing for 4 seconds, after which the
equipment will exit the procedure;
•
Disconnect the equipment from the mains power
supply.
To exit the procedure before its completion:
•
Keep the
seconds during the procedure (or rather before
setting "1": the restoring of default factory settings will
not be carried out).
within
timeslots,
and the
keys pressed for 4
key;
or the
key or do not carry
and the
keys pressed for 4
or the
key;
or the
key to either
key or do not carry
and the
keys pressed for 4
the
keyboard
is
not
and the
keys pressed for 4
key;
or the
key or do not carry
and the
pressed for 4
key;
or the
key or do not carry
and the
key pressed for 4
it
is
key
key.
the
locked
key
Advertisement
