Maximum Controls MAX 1200FS PRO Installation Manual page 40

miller RBAND monitored WIRELESS
Channel 1 & 2 transmitters
MUST be programmed by
RBAND receiver. See below or
Miller Edge Wireless RBAND
instruction sheet to program
transmitters to receiver.
OPEN ONLY
OPEN ONLY
PHOTO CLS
O OPEN ONLY O O O O
24VDC OUTPUT
GND
OPEN/CLS
12VDC OUTPUT T T
GND
BATTERY
MATRIX III
BATTERY VOLTAGE AGE
INPUT
ERROR
E 1/2 F F
BA BATTERY
BATTERY
INPUT IN
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
RE REPLACE
LEAVE
BATTERY ERY
B BATTERY
CLOSED
TEST ST
POW POWER /
SOLAR IN SOL
POWER
ERD SENSITIVITY
14 12 12 14 12
16
16
MIN MIN
ERD ERD
1 9 1 9
MAX MOTOR MAX MOTOR
MODULE MO
SENSE OVER SENSE OVER
P PORT 3 7 3 7
LOAD LOAD MIN MIN
OPENING OPEN CLOSING
OBD PORT D POR
BLACK BOX ACK B
MAXIMUM CONTROLS
RESET
OFF
DSP ARM CONTROLLER
1
ON/OFF ON/O
2
BATTE BATTERY
ALARM 3
4
5 MOTION CONTROL
PROGRAMMING OGRA
ID PLUG
6
ERROR
1
2
3
ID
4
PLUG 5
6
OPEN EN
7 OPEN STOP CLOSE
P PROGRAM
8
9
10
OFF
ANTI-
PUSH PULL MAGLOCK
EXIT PWR
TAILGATE
SOLAR MODE S OPEN OPEN
EXIT LOOP
OFF ON
GND
O OFF ON
GATE
CENTER LOOP
OFF
LOOP PWR CLOSING GATE SPEED
OPERATOR
SAFETY LOOP
MIN MIN
FAULTS
MAX MAX
SINGLE DUAL
24VDC OUTPUT
GND MOTOR 1 MOTOR 2
12VDC OUTPUT
GND
4. Press the transmitter program button for ~2 seconds. The receiver will beep. Wait 10 seconds for an additional beep to complete
programming.
5. To program a transmitter to channel 2, press and hold the receiver program button until the second beep, then release the button.
The R2 LED should be on. Repeat step 4 for channel 2 transmitter.
ERASE PROGRAMMING. If you need to replace a transmitter or you have any other programming issues, you may need to erase the receiver.
1. To erase transmitters programmed into the receiver, use a screwdriver to short the two pins marked MR next to the DIP-switches.
2. While shorting the pins, press and hold the program button for several seconds; you will hear a series of 10 beeps followed by a rapid
chirping sound.
3. When the chirping stops, release the program button. Wait ~10 seconds and you will hear 2 beeps. The receiver is now ready to be
reprogrammed.
GND ANT
CHECK
RBAND Receiver
12/24 AC/DC
12/24 AC/DC
+ -
+ -
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
+ -
+ - CS1 C1 BS1 CS2 C2 BS2 NO3 C3
CS1 C1 BS1 CS2 C2 BS2 NO3 C3
12/24 AC/DC
12/24 AC/DC
NC
NC
NC
OPEN/CLS NC
12VDC OUT
GND
10K
C CLS ONLY C 10K
10K
12VDC OUT
GND
Channel 1 - CLS ONLY 10K
[+] +]
MOTOR 1 CLOSING direction ONLY
INPUTS [-] ]
MOTOR 2 [+]
MUST be LEARNED to monitor sensor,
INPUTS [-]
LIMIT 1
See Step , page 12.
MOTOR 1 12
LIMIT 2
LIMIT 1
MOTOR 2
CLOSE
LIMIT 2
TIMER
Channel 2 - OPEN ONLY 10K
LIMIT 1
OPENING direction ONLY
MAX MOTOR 1
GND
OFF
LIMITS
LIMIT 2
MUST be LEARNED to monitor sensor,
LIMIT 1
MOTOR 2
GND
LIMITS
LIMIT 2
See Step , page 12.
12
JOG JOG
GATE OPEN
COM
GATE CLOSED
GND
CLOSE CL
NO
MAG
LOCK COM
NC
AGLOCK
DELAY ELAY
OPEN ONLY NC
PHOTO CLS NC
2.5 sec 2.5 s OPEN / CLS NC
1.5 sec sec
12VDC OUT
Wireless Receiver/Transmitter Programming:
GND
OPEN ONLY 10K
UL
ENTRAP AP
CLS ONLY 10K
OPEN / CLS 10K
1. Make sure receiver and transmitters have power.
12VDC OUT
GND
2. Green power LED will be blinking on channel 1 transmitter (unlearned).
3. To enter learn mode, press and hold the receiver program button for ~2 seconds until the
R1 LED turns on, then release the button.
PROG
R1
R2
MR ON DIP
DIP-Switches
1-ON
1-ON
1 2 3 4
1 2 3 4
2-ON
2-OFF
R3 ATEST
R3 ATEST
3-ON
3-ON
4-OFF
Com ATEST
Com ATEST
Com ATEST
Com ATEST
Wire 10K Edges
Program Button
Green LED
Mount on Gate's
CLOSING side.
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2c
31
32
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2.2G
S e
n c o
n d
s o l
t r a
d s
n s m
e p
a r a
i t t e
t e l
r
y
T r a
n s m
i t t e
r
v e r
c e i
R e
RBAND
Transmitter
MGL-TX20
Terminal Block
Connection
Polarity does
NOT matter.
Mount on Gate's
OPENING side.
A RBAND transmitter is
needed for each channel of
the receiver.