Maximum Controls MAX 1200FS PRO Installation Manual page 23

gate tamper feature
Many different safety devices can be wired to the GATE TAMPER. After device is wired to relay, it MUST be ARMED to function.
Wiring Gate Tamper
The GATE TAMPER can be used for various functions such as
turning a warning light, siren or camera on when the gate is
tampered with (Vandalized Gate).
The gate operator defines a "Vandalized Gate" as UNAUTHORIZED
movement of the gate. This can occur if the chain is dropped and
gate is manually moved from the closed position or the gate is
forced open from the closed position without authorization.
TAMPER NO/Com Relay: Connect a warning light, siren, camera or
an existing alarm system to relay.
TAMPER IN/GND Input: Connect a sensor device to input. When
Tamper In/GND gets triggered, device that is wired to Tamper relay
(NO/Com) will activate.
Existing
Building
Alarm
System
Power
Arm Gate Close Tamper (Turn ON)
GATE TAMPER
ON
NOT
Turn ON 5
OPERATOR ALARM and GATE TAMPER
OFF
GATE TAMPER
Warning
Siren
Light
Power
OFF MUST
GATE TAMPER
OFF
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
OFF
GATE TAMPER
MUST
Alarm Reset Button
Motion
Security
Sensor
Camera
BATTERY
BATTERY VOLTAGE
INPUT
E 1/2
ERROR
BATTERY
INPUT
BATTERY
IN USE
BATTERY
POWER /
TEST
POWER
SOLAR IN
14
16
MIN
1
MAX
MODULE
SENSE
3
PORT
OPENING
OBD PORT
RESET /
BLACK BOX
MANUAL
RELEASE OFF
1
2
ALARM 3
4
5 PROGRAMMING
ID PLUG
6
ERROR
1
2
3
ID
4
PLUG 5
6
7
PROGRAM
8
9
10
OFF
EXIT PWR
SOLAR MODE
EXIT LOOP
GND
OFF
CENTER LOOP
LOOP PWR
SAFETY LOOP OPERATOR
FAULTS
PRIMARY SECONDARY
24VDC OUTPUT
GND
12VDC OUTPUT
GND
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2c
15
15
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2.2G
BATTERY
MATRIX III
BATTERY VOLTAGE
INPUT
ERROR E 1/2 F
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY
BATTERY
POWER / CLOSED
TEST
POWER
SOLAR IN
ERD SENSITIVITY
14 12 14 12
16 16
MIN MIN
ERD ERD
1 9 1 9
MAX MAX
MODU MODULE MOTOR MOTOR
SENSE OVER SENSE OVER
3 7 3 7
PORT PORT
LOAD LOAD
OPENING CLOSING
OBD PORT
RESET / RESET /
BLACK BOX
MANUAL MANUAL MATRIX III
RELEASE RELEASE
SWING / SLIDE
1 1
2 2
ALARM ALARM 3 3
4 4
MOTION CONTROL
5 5 PROGRAMMING PROGRAMM
ID PLUG ID PLUG 6 6
ERROR ERROR
1 1
2 2
ID ID 3 3
4 4
PLUG G 5 5
6 6
7 OPE OPEN STOP CLOSE
PROGRAM PROGRAM
8
9
10
OFF
QUICK QUICK
EXIT PWR EX OPEN OPEN
SOLAR MODE LAR MODE CLOSE CLOSE
LEFT RIGHT
LOOP
OFF OFF ON ON
OFF ON
GATE GAT
LOOP LOOP
LOOP PWR LOOP PWR GATE SPEED GATE SPEED
LOOP LOOP OPERATOR O
MIN MIN MIN
MAX MAX MAX
PRIMARY PRIMARY SECONDARY SECONDA
24VDC OUTPUT 24VDC OUTPUT
GND GND OPENING CLOSING OSING
12VDC OUTPUT OUTPUT
GND
LINK
OK OK
PRIMARY/ PRIMARY/
SECONDARY SECONDARY
LINK LINK
MATRIX III
F
BATTERY
BACKUP MODE
LEAVE OPEN
OPEN 1 TIME
REPLACE
LEAVE
BATTERY
CLOSED
CLOSE
ERD SENSITIVITY
TIMER
12 14 12
16
MIN
ERD ERD
9 9
1
MOTOR MAX MOTOR
SENSE
OVER OVER
3
7 7
MIN MAX
LOAD LOAD
CLOSING
OFF
MATRIX III
SWING / SLIDE
ON/OFF
BATTERY
MOTION CONTROL JOG
LEFT RIGHT
OPEN STOP CLOSE
QUICK MAGLOCK
OPEN OPEN
CLOSE DELAY
LEFT RIGHT
OFF ON
ON
GATE
OFF 2.5 sec
GATE SPEED
1.5 sec
MIN MIN
MAX MAX
UL
ENTRAP
OPENING CLOSING
LINK
OK
PRIMARY/
SECONDARY
LINK
Gate Tamper LEDs
MOTOR
INPUTS
MOTOR
POSITION
INPUTS
CLOSE
TIMER
SLIDER
LIMIT
MIN MAX SWING
OFF LIMIT
ON/OFF
BATTERY
JOG
GATE OPEN
COM
GATE CLOSED
GND
LEFT RIGHT
NO
MAG
LOCK COM
NC
MAGLOCK
DELAY
OPEN ONLY NC
PHOTO CLS NC
OPEN/CLS NC
OFF 2.5 sec
1.5 sec 12VDC OUT
GND
OPEN ONLY 10K
UL
ENTRAP EN CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
GND
MOTOR
INPUTS
MOTOR
POSITION
INPUTS
SLIDER
LIMIT
SWING
LIMIT
GATE OPEN
COM
GATE CLOSED
GND
NO
MAG
LOCK COM
NC
OPEN ONLY NC
PHOTO CLS NC
OPEN/CLS NC
12VDC OUT
GND
OPEN ONLY 10K
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
GND