Maximum Controls MAX 1200FS PRO Installation Manual page 14

3
ground operator
Operator MUST be Properly GROUNDED
IMPORTANT: Operator MUST be grounded in lightning
prone areas or warranty will be VOIDED!
WARNING
connect chassis
to ground rod for
lightning protection
Proper grounding of this gate operator is a requirement for
LIGHTNING PROTECTION in lightning prone areas. To be effective,
ground connections should be made with a minimum 12 AWG, 600
volt insulated wire to a ground point within 3 feet of the gate
operator. The ground point must be at an electrical panel, a
metallic cold water pipe that runs in the earth, or a grounding rod.
NOTE: Consult city codes for AC line wiring.
Beware of existing underground services.
4
opening direction /id plug/operator
OPEN LEFT
ID Plug Error: If ID plug is NOT
plugged in, board will constantly
beep and operator will NOT
function.
ID plug MUST be plugged in.
Operator:
Set operator to PRIMARY for a single operator installation.
Set EACH Matrix III board for desired operator positions
when bi-parting gates are installed.
NOTE: PRIMARY board settings will override secondary
board settings if a conflict in settings occurs.
Set the desired opening direction.
BATTERY
INPUT
POWER /
SOLAR IN
MODULE
PORT
RESET /
MANUAL
RELEASE
ALARM
ID PLUG
ERROR
ID
PLUG
10
EXIT PWR
1700 FS PRO
EXIT
GND
ID Plug
CENTER
LOOP PWR
SAFETY
FAULTS
24VDC OUTPUT
GND
12VDC OUTPUT
GND
within 3 ft
of operator.
Grounding Rod
Any of the THREE Chassis Grounds can be used. They are located next
to the gear reducer. DO NOT remove any existing green ground wires.
OPEN OPEN
LEFT RIGHT
BATTERY Y MATRIX III A
BATTERY VOLTAGE BATTERY V
INPUT
E E 1/2 1/2 F
ERROR
BATTERY
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE R
LEAVE
BATTERY ATTERY
BATTERY B
CLOSED
TEST TEST
POWER
ERD SENSITIVITY ER
14 12 12 14 12
16 16
MIN MIN
ERD E ERD
9 9 9
1 1
MAX MOTOR MO MAX MOTOR
SENSE OVER OV SENSE OVER
3 3
7 7 7
LOA LOAD LOAD
OPENING CLOSING
OBD PORT
BLACK BOX
MA MATRIX III
OFF
SWING / SLIDE SWI
1
2
3
4
5 PROGRAMMING MO MOTION CONTROL
6
1
2
3
4
5
6
7
OPEN PEN STOP CLOSE
PROGRAM
8
9
OFF
QUICK K
OPEN OPEN
SOLAR MODE
CLOSE LEFT RIGHT
LOOP
OFF ON ON
OFF ON
GATE
LOOP
GATE SPEED
LOOP OPERATOR
MIN MIN
MAX MAX
PRIMARY SECONDARY
OPENING CLOSING
LINK
OK
PRIMARY/
SECONDARY
LINK
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2c
6
6
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2.2G
Ground
1 2
3
L
I
M
I
T
S
E
N
S
O
R
MOTOR
INPUTS
MOTOR
POSITION
INPUTS
CLOSE
TIMER
SLIDER
LIMIT
SWING
MIN MAX
OFF
LIMIT
Breather
ON/OFF
BATTERY Pin
JOG
GATE OPEN
COM
GATE CLOSED
GND N
I O
LEFT RIGHT
MAG NO
U T
LOCK
COM
C A
V E
NC
MAGLOCK
M O
DELAY
R E
R E
OPEN ONLY NC
F O
PHOTO CLS NC
B E I O N
OPEN/CLS NC A T
OFF 2.5 sec
E R
1.5 sec
12VDC OUT
O P
GND
OPEN ONLY 10K
UL
ENTRAP CLS ONLY 10K
OPEN/CLS 10K
IMPORTANT:
12VDC OUT
Remove breather pin
GND
from gear reducer
BEFORE cycling
operator.
ul e
M od
ry
tte
Ba
ry IN
tte
Ba Er ro r
TE ST
tte ry
pl ac e Ba
F
Re ry
1/ 2 /O FF Ba tte
ON ry
tte
E Ba
OPEN RIGHT