Maximum Controls MAX 1200FS PRO Installation Manual page 27

This page and the next 3 pages can help troubleshoot problems that might occur after installation is complete.
usb black box port
Download a simple .txt file to troubleshoot gate operator errors and view event history.
BATTERY MATRIX III
BATTERY VOLTAGE
INPUT
ERROR E 1/2 F
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY
BATTERY
POWER /
CLOSED
TEST
POWER
SOLAR IN
ERD SENSITIVITY
14 12 14 12
16 16
MIN MIN
ERD ERD
1 9 1 9
MAX MOTOR MAX MOTOR
MODULE
SENSE SENSE
OVER OVER
3 7 3 7
PORT
LOAD LOAD
OPENING CLOSING
OBD PORT
RESET /
BLACK BOX
MANUAL MATRIX III
RELEASE OFF
SWING / SLIDE
1
2
3
ALARM
4
MOTION CONTROL
5 PROGRAMMING
ID PLUG
6
ERROR
1
2
3
ID
4
PLUG 5
6
7
OPEN STOP CLOSE
PROGRAM
8
9
10
OFF
QUICK
OPEN OPEN
EXIT PWR
SOLAR MODE
CLOSE LEFT
EXIT LOOP
OFF ON
GND
OFF ON
GATE
CENTER LOOP
LOOP PWR
GATE SPEED
SAFETY LOOP OPERATOR
MIN MIN
FAULTS
MAX MAX
PRIMARY SECONDARY
24VDC OUTPUT
GND OPENING CLOSING
12VDC OUTPUT
GND
LINK
OK
PRIMARY/
SECONDARY
LINK
test entrapment sensors
Troubleshoot entrapment protection sensors:
1. Press and HOLD the STOP button & then the OPEN button together until beeping is heard, learn mode begins.
NOTE: DO NOT press the OPEN button before the STOP button or learn mode will NOT function.
2. LEDs should be ON if an entrapment sensor is detected in EACH input.
If LEDs are NOT on, sensors have a problem.
Possible problems:
• Photocells are out of alignment
• Photocells are wired wrong - N.C. or N.O. depending on which
photocells are used, see specific mfg instructions.
• Sensor is bad
3. Press STOP button again within 5 min. to end learn mode, beeping stops.
NOTE: If STOP button is not pressed within 5 min. learn mode automatically end after 5 min.
troubleshooting
MOTOR
INPUTS
MOTOR
POSITION
INPUTS
CLOSE
TIMER
SLIDER
LIMIT
SWING
MIN MAX
OFF
LIMIT
ON/OFF
BATTERY
JOG
GATE OPEN
COM
GATE CLOSED
GND
LEFT RIGHT
NO
MAG
LOCK
COM
NC
MAGLOCK
DELAY M A
RIGHT
OPEN ONLY NC
PHOTO CLS NC F l a
OPEN/CLS NC
OFF 2.5 sec
s h
1.5 sec 12VDC OUT
GND
D r i
OPEN ONLY 10K
UL
ENTRAP CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
GND
1. Plug MAX USB flash drive into OBD port. OBD LED will flash while file is downloading.
Remove flash drive after LED stops flashing (up to 5 minutes to download).
2. Plug flash drive into any computer USB port OR smart phone using a USB phone adapter.
The most recent 8000 events can be viewed. No special software required.
S m
a r t
P h o
n e
n e
h o C o m
B P
U S
e r
a p t
d
A d
i r e
q u
R e
O R
X
v e
O O O O O OPEN ONLY NC
P P P PHOTO CLS P NC
OPEN/CLS NC
12VDC OUT
GND
OPEN ONLY 10K
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
GND
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2c
19
19
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2.2G
Event History Text Document Sample
INFO:
WARNING:
ERROR:
ENTRAP:
Event Report:
Fri 07/11/2014 10:59:41 INFO : Cycle Counter
Fri 07/11/2014 10:59:41 ENTRAP : SEC_MC: First ERD Detected
p u t
e r
Fri 07/11/2014 10:57:38 ENTRAP : PRI_MC:
Fri 07/11/2014 10:56:46 WARNING: PRI_MC: Tamper Reported
Fri 07/11/2014 10:56:36 WARNING: PRI_MC: Tamper Reported
Fri 07/11/2014 10:56:33 ENTRAP : PRI_MC:
Fri 07/11/2014 10:56:33 ENTRAP : PRI_MC:
MOTION CONTROL
OPEN STOP
Factory Learned Input
Factory Learned Input
IMPORTANT:
Unlearned Input
devices MUST be
Monitored Power
powered by Matrix III
or they will NOT be
MONITORED.
Unlearned Input
Unlearned Input
Unlearned Input
MOTION CONTROL
STOP
OPEN CLOSE
CLOSE
Sensing