Maximum Controls MAX 1200FS PRO Installation Manual page 32

omron E3K-R10K4 wiring for max pro
UL325-2016
PRE 2018 WITHOUT Built-in Resistor
NORMALLY CLOSED (NC) NORMALLY CLOSED (NC)
Wiring to E3K Photocell Wiring to E3K Photocell
OPENING
Photocell (Reflector)
Installation Steps: Installation Steps:
OPEN ONLY NC
PHOTO CLS NC
OPEN/CLS NC
12VDC OUT
GND
GND
OPEN ONLY 10K
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
GND
NOTE: NOTE:
DO NOT use 10K Resistor included with photocell. DO NOT use 10K Resistor included with photocell.
Direction
Set switch to Set switch to
"LIGHT ON" "LIGHT ON"
LIGHT ON LIGHT ON
DARK ON DARK ON
Min Min Max Max
SENSITIVITY SENSITIVITY
Sensitivity Adjustment: Sensitivity Adjustment:
If the photocell does not respond to an If the photocell does not respond to an
obstruction, lower the sensitivity by obstruction, lower the sensitivity by
turning adjustment counter-clockwise. turning adjustment counter-clockwise.
connect connect
DO NOT DO NOT
to NC1 #3. to NC1 #3.
Power Power
C-1 NO1 NC1 C-1 NO1 NC1
1 1 2 2 3 3 4 5 6 4 5 6
24 to 240 VAC 24 to 240 VAC
24 to 240 VDC 24 to 240
C-1 C-1 NO1 NO1
12VDC Out Monitored 12VDC Out Monitored
Polarity does NOT matter
GND
IMPORTANT: IMPORTANT:
Photocell MUST be powered Photocell MUST be powered
by 12VDC OUT Monitored or by 12VDC OUT Monitored or
it will NOT be MONITORED. it will NOT be MONITORED.
PRE 2018 WITHOUT Built-in Resistor
NORMALLY CLOSED (NC) NORMALLY CLOSED (NC)
Wiring to E3K Photocell Wiring to E3K Photocell
Installation Steps: Installation Steps:
VDC
OK to OK to
use use
12VDC 12VDC
OPEN ONLY OPEN ONLY
PHOTO CLS
OPEN/CLS OPEN/CLS
12VDC OUT 12VDC OUT
OPEN ONLY OPEN ONLY
CLS ONLY CLS ONLY
OPEN/CLS OPEN/CLS
12VDC OUT 12VDC OUT
NOTE: NOTE:
DO NOT use 10K Resistor included with photocell. DO NOT use 10K Resistor included with photocell.
24
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version
24
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2.2G
CLOSING Direction
Photocell (Reflector)
Set switch to Set switch to
"LIGHT ON" "LIGHT ON"
LIGHT ON LIGHT ON
Min Min Max Max
SENSITIVITY SENSITIVITY
Sensitivity Adjustment: Sensitivity Adjustment:
If the photocell does not respond to an If the photocell does not respond to an
obstruction, lower the sensitivity by obstruction, lower the sensitivity by
turning adjustment counter-clockwise. turning adjustment counter-clockwise.
connect connect
DO NOT DO NOT
to NC1 #3. to NC1 #3.
C-1 NO1 NC1 C-1 NO1 NC1
1 1 2 2 3 3 4 5 6 4 5 6
C-1 C-1 NO1 NO1
NC NC
NC
NC NC
12VDC Out Monitored 12VDC Out Monitored
GND GND
Polarity does NOT matter
GND GND
10K 10K
10K 10K
10K 10K
IMPORTANT: IMPORTANT:
Photocell MUST be powered
Photocell MUST be powered
GND GND
by 12VDC OUT Monitored or by 12VDC OUT Monitored or
it will NOT be MONITORED. it will NOT be MONITORED.
DARK ON DARK ON
Power Power
24 to 240 VAC 24 to 240 VAC
24 to 240 VDC 24 to 240 VDC
OK to OK to
use use
12VDC 12VDC
Rev 09-28-2023