LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, BOTH OF WHICH ARE EXPRESSLY DISCLAIMED. In no event shall Spectra Logic be liable for any loss of profits, loss of business, loss of use or data, interruption of business, or for indirect, special, incidental or consequential damages of any kind, even if Spectra Logic has been advised of the possibility of such damages arising from any defect or error.
Page 3
Contacting Spectra Logic Spectra Logic Web Site: www.spectralogic.com United States Headquarters Spectra Logic Corporation 1700 North 55th Street Boulder, CO 80301 Phone: (800) 833-1132 or (303) 449-6400 International: 00.1.303.449.6400 Fax: (303) 939-8844 SpectraGuard Technical Support Web Site: www.spectralogic.com/support Knowledge Base: www.spectralogic.com/knowledgebase...
Introduction The library contains a single Library Control Module (LCM). The LCM provides the logic and circuitry to display the user interface on the library’s touch screen. The LCM includes an embedded web server to provide remote access to the user interface through the Remote Library Controller (RLC) using a standard web browser.
A new LCM module Note: After removing the new LCM from its packaging, keep the packaging to return the old LCM to Spectra Logic. Power off the Library To power off the library, press and hold the front panel power button approximately six seconds or until the button’s LED starts flashing.
Page 7
2. Using your fingers or a #2 Phillips screwdriver, loosen but do not remove the captive screws that secure the bottom of the cover to the chassis. Figure 3 The rear panel cover and screws (T380 shown). 3. Lift the cover outward and away from the chassis to disengage the two nuts extending from the back of the cover from the holes on either side of the chassis (see Figure...
Locate a Saved Library Configuration The following options are described in the Spectra T200, T380, & T680 Library User Guide. Spectra Logic highly recommends that you save your library configuration settings to a safe location. Do not attempt to save the library configuration if the LCM is Caution malfunctioning.
Page 9
2. Using a #2 Phillips screwdriver, tighten the screws, shown in LCM to the chassis. 3. Return the malfunctioning LCM to Spectra Logic as described in Components on page Install the Rear Cover 1. Lift the cover and align it so that the two nuts extending from the back of the cover...
After the library restarts, restore the partition definitions and library configuration settings using one of the following methods. Via USB—Restore the configuration you previously saved to a USB storage device or uploaded to a file on a computer (see page 11).
Figure 7 USB port location. 1. Locate the LCM. 2. Correctly orient and plug the USB storage device into the USB port on the LCM. Restoring a Saved Configuration Follow these steps to restore the library settings with a saved configuration.
Option Use this option to... Upload Backup Use the button at the top of the screen to upload a configuration Configuration file that you previously saved on a computer to a temporary location in the library memory. Note: must then run the Restore Library Configuration from Backup Configuration File utility to restore the library configuration.
Page 13
2. Using a #1 Phillips screwdriver, remove the two screws securing the protective cover plate to the LCM (Figure Figure 8 Compact flash card cover plate and screws. 3. Remove the cover and set it aside. 4. Push the eject button to eject the compact flash card from the LCM Figure 9 The compact flash eject button and slot.
7. Position the protective cover against the LCM, aligning the screw holes in the cover with those on the LCM (see 8. Using a #1 Phillips screwdriver, install the two screws to secure the protective cover plate to the LCM. 9.
Page 15
Representative for details (additional charges may apply). 1. Obtain a Return Materials Authorization (RMA) number from you SpectraGuard Technical Support representative. Spectra Logic needs this number to identify the part on its arrival. 2. Place the LCM inside the anti-static bag.
Page 16
International Return Instructions 1. Fill out your portion of the International Shipping Instructions form, available on the Spectra Logic Web site at www.spectralogic.com/returns. 2. Return the completed form to Spectra Logic using one of the following methods: Email: intlreturns@spectralogic.com Fax: 303.939.8844...