Loewe Connect 32 3D Operating Instructions Manual page 24

Initial installation
Setting options for DVB-C reception:
If you have not selected a DVB-C antenna in the antenna selection: Con-
tinue with Setting options for DVB-S reception (see right hand column).
Network If several networks are available over DVB-C, you can
selection decide which network you want to receive your channels
from. The normal DVB-C settings are derived from the
selection of the location or network and do not need to
be changed. Exactly which of the following settings are
present is dependent on which network is selected.
Select network,
OK Proceed.
Settings
INITIAL INSTALLATION (DVB-C)
Scrambled stations
Search method
Start frequency
Network ID
Symbol rate 1 (DVB-C)
Symbol rate 2 (DVB-C)
QAM modulation 1
QAM modulation 2
Proceed
OK
Select and adapt settings for DVB-C reception.
Encrypted You can state whether coded stations are to be searched
stations
for in the search/update.
scrambled stations. However, these stations can only be
received in connection with a CA module and the appro-
priate Smart Card.
on page 65.
If a CA module with a SmartCard is already plugged in for
the station search, all the stations which this module can
descramble are also saved when no is preset.
Search If you want to run the station search independently of
method the channel grid, select frequency search for the search
method.
Start The DVB stations are only searched for in the frequency
frequency range above the start frequency.
Network ID Only change these defaults if you are familiar with other
symbol rates and types of modulation or if you have to
Symbol rate specify the network ID for your cable network. In the
case of small cable networks fed directly from the satel-
QAM lite, the rate of 6900 might have to be replaced by 6111.
modulation Your cable provider has the information you need.
OK Proceed.
- 24
no yes
Channel search
047.0 MHz
none
6875
6900
64
256
Select yes to save all found
Handling of the CA module is described
Setting options for DVB-S reception:
If you have not selected a DVB-S antenna in the antenna selection:
Continue with Setting options for all types of reception on page 30.
The normal DVB-S settings are derived from the selection
of the location and do not need to be changed in most
cases.
Select
INITIAL INSTALLATION (DVB-S)
satellite
Select satellite installation
installation Single satellite
2 satellites on 22 kHz switchbox
2 satellites on toneburst switch
Max. 4 satellites on DiSEqC multiswitch
DiSEqC one cable communal system
other communal installation
Proceed
OK
Selecting the satellite system.
Specify how you receive which satellite(s) (single
satellite or type of satellite system). Ask your dealer
if required.
Single Reception of a single satellite via a connected LNC (LNB).
See page 25 for settings.
satellite
Reception of two different satellites with two LNCs (LNBs)
2 satellites
on 22 kHz which are connected to the TV set by a 22 kHz switchbox.
See page 25 for settings.
switchbox
Reception of two different satellites with two LNCs (LNBs)
2 satellites
on toneburst which are connected to the TV set by a toneburst switch.
See page 25 for settings.
switch
The TV set controls a DiSEqC multiswitch to which up to
Max. 4
satellites four LNCs (LNBs) for different satellites are connected.
See page 26 for settings.
on DiSEqC
multiswitch
DiSEqC Select setting if the TV set is connected to a DiSEqC
single-cable system (according to EN 50494). Several Sat
one cable
communal receivers can be connected to one Sat cable. See page
27 for settings.
system
Select setting if the TV set is connected to a single-cable
other
communal system (without DiSEqC). Several Sat receivers can be
connected to one Sat cable. Unlike a DiSEqC single-cable
installation
system there are restrictions in the range of certain recep-
tion frequencies in single-cable community systems. See
page 28 for settings.
OK Proceed
(to the appropriate page of the satellite system).
OK
Back