Lighting The Side Burner; Lighting The Spit Burner - Barbecook SIESTA 612 black edition Manual

5. Set the control knob of one burner to HIGH.
Always light one main burner to start with. Never light all
main burners at the same time.
6. lf the burner does not light within 5 seconds, set its control
knob to OFF, close the gas supply and wait 5 minutes. This
allows any accumulated gas to escape.
7. Retry lighting the burner. lf it still does not light, refer to "14
Troubleshooting" to determine the cause of the problem.
8. Once one burner is lit, light the other burners by setting their
control knobs to HIGH.

9.3 Lighting the side burner

The side burner can only carry pots with a maximum
weight of 9 kg, maximum diameter of 220 mm and
minimum diameter of 120 mm.
9.3.1 u
sing the igniter
1. Open the lid and set the control knob of the side burner to
OFF.
2. If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
3. Push in the control knob of the side burner, set it to HIGH
and hold it for a moment. The build-in igniter will cause
sparks, which will light the side burner.
4. If the burner does not light after three attempts, set its
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
5. Retry lighting the side burner. If it still does not light, try
lighting it with a match or refer to "14 Troubleshooting" to
determine the cause of the problem.
9.3.2 u
sing A mAtCh
1. Place a match in the match holder.
2. Open the lid and set the control knob of the side burner to
OFF.
3. lf no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
4. Light the match and hold it about 13 mm from the side
burner.
5. Set the control knob of the side burner to HIGH.
6. lf the side burner does not light within 5 seconds, set
its control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
7. Retry lighting the side burner. lf it still does not light, refer to
"14 Troubleshooting" to determine the cause of the problem.

9.4 Lighting the spit burner

Before you can use the spit burner, you have to install
two D batteries in the spit burner engine. These batteries
are not supplied with the appliance.
9.4.1 u
sing the igniter
1. Open the lid and set the control knob of the spit burner to
OFF.
2. Remove the grills and warming rack from the appliance and
put them aside.
3. If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
4. Push in the control knob of the spit burner, set it to HIGH
and hold it for a moment. The build-in igniter will cause
sparks, which will light the spit burner.
5. If the burner does not light after three attempts, set its
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
6. Retry lighting the spit burner. If it still does not light, try
lighting it with a match or refer to "14 Troubleshooting" to
determine the cause of the problem.
9.4.2 u
sing A mAtCh
1. Place a match in the match holder.
2. Open the lid and set the control knob of the spit burner to
OFF.
3. If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
4. Light the match and hold it to the right of the spit burner.
5. Set the control knob of the spit burner to HIGH.
6. If the burner does not light within 5 seconds, set its control
knob to OFF, close the gas supply and wait 5 minutes. This
allows any accumulated gas to escape.
7. Retry lighting the spit burner. If it still does not light, refer to
"14 Troubleshooting" to determine the cause of the problem.
11