Self-Diagnosis Code Table - Sony DCR-TRV7 Service Manual

4. Self-diagnosis Code Table

Self-diagnosis Code
Block Detailed
Function Code
0 0
C 2 1 Condensation.
0 0
C 2 2 Video head is dirty.
0 0
C 2 3 Non-standard battery is used.
LOAD direction. Loading does not complete
1 0
C 3 1
within specified time
UNLOAD direction. Loading does not com-
1 1
C 3 1
plete within specified time
C 3 1 2 0 T reel side tape slacking when unloading.
Winding S reel fault when counting the rest
2 1
C 3 1
of tape.
2 2
C 3 1 T reel fault
2 3
C 3 1 S reel fault
2 4
C 3 1 T reel fault
3 0
C 3 1 FG fault when starting capstan
4 0
C 3 1 FG fault when starting drum
4 2
C 3 1 FG fault during normal drum operations
C 3 1 1 0 LOAD direction loading motor time-out
C 3 1 1 1 UNLOAD direction loading motor time-out
C 3 2 2 0 T reel side tape slacking when unloading.
Winding S reel fault when counting the rest
C 3 2 2 1
of tape.
C 3 2 2 2 T reel fault
C 3 2 2 3 S reel fault
C 3 2 2 4 T reel fault
C 3 2 3 0 FG fault when starting capstan
C 3 2 4 0 FG fault when starting drum
C 3 2 4 2 FG fault during normal drum operations
Difficult to adjust focus
E 6 1 0 0
(Cannot initialize focus.)
Zoom operations fault
E 6 1 1 0
(Cannot initialize zoom lens.)
Steadyshot function does not work
E 6 2 0 0 well.(With pitch angular velocity sensor
output stopped)
Steadyshot function does not work
2
E 6 0 1 well.(With yaw angular velocity sensor
output stopped)
Symptom/State
— 6 —
Correction
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Use the InfoLITHIUM battery.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Remove the battery or power cable, connect, and perform operations from the
beginning.
Inspect the lens block focus reset sensor (Pin 3 of CN101 of CD-168 board)
when focusing is performed when the focus dial is rotated in the focus manual
mode and the focus motor drive circuit (IC402, IC403 of CB-58 board) when the
focusing is not performed.
Inspect the lens block zoom reset sensor (Pin !• of CN101 of CD-168 board)
when zooming is performed when the zoom lens is operated and the zoom motor
drive circuit (IC402, IC403 of CB-58 board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE501 of CD-168 board) peripheral circuits.
Inspect yaw angular velocity sensor (SE500 of CD-168 board) peripheral circuits.