Self-Diagnosis Code Table - Sony DCR-TRV16 Service Manual

Ver 1.2 2003. 11
4.

SELF-DIAGNOSIS CODE TABLE

Self-diagnosis Code
Block Detailed
Function Code
C 0 4 0 0
C 2 1 0 0
C 2 2 0 0
C 3 1 1 0
C 3 1 1 1
C 3 1 2 0
C 3 1 2 1
C 3 1 2 2
C 3 1 2 3
C 3 1 2 4
C 3 1 3 0
C 3 1 4 0
C 3 1 4 2
C 3 2 1 0
C 3 2 1 1
C 3 2 2 0
C 3 2 2 1
C 3 2 2 2
C 3 2 2 3
C 3 2 2 4
C 3 2 3 0
C 3 2 4 0
C 3 2 4 2
E 6 1 0 0
E 6 1 1 0
E 6 2 0 0
E 6 2 0 1
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting the
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor time-
out.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
Winding S reel fault when counting the
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drum
operations
Difficult to adjust focus
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Inspect the lens block focus reset sensor (Pin qk of CN1201 of VC-
280 board) when focusing is performed when the focus ring is rotated
in the focus manual mode, and the focus motor drive circuit (IC1204
of VC-280 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin 9 of CN1201 of
VC-280 board) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC1204 of VC-280
board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE5302 of JK-217 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE5301 of JK-217 board)
peripheral circuits.
1-3E
Correction