Storing And Changing Data In The Memory; Storing And Changing The Preset Data - Ikegami HTM-1517R Operation Manual

4-4. Storing and Changing Data in the Memory

(1) Storing and changing the PRESET data

<Example 1> Changing the MK.PHASE, H.CENT, V.CENT, WIDTH, HEIGHT, TRAPEZOID and SIDE PIN.
INPUT SELECT MONO
DIGI YPbPr/RGB SPLIT APT
A
1
B
2nd
TEST COMB MARK
C SLOT
EXT
STNC
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
2
CHROMA CONT
GAIN
AUTO
ASP
SET UP
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
3
CHROMA CONT
GAIN
AUTO
ASP
SET UP
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
4
CHROMA CONT
GAIN
AUTO
ASP
SET UP
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
5
CHROMA CONT
GAIN
AUTO
ASP
SET UP
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
6
CHROMA CONT
GAIN
AUTO
ASP
SET UP
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
7
CHROMA CONT GAIN
AUTO
ASP
SET UP
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
8
CHROMA CONT
GAIN
AUTO
ASP
SET UP
D I S P L AY S E L E C T
MENU ENT ESC U . DISPLAY
HUB BLIGHT BACK GRAND
9
CHROMA CONT
GAIN
AUTO
ASP
SET UP
Note
The MK.PHASE, H.CENT, V.CENT, WIDTH, HEIGHT, TRAPEZOID and SIDE PIN data are stored as separate data items for each signal
format, scan size or aspect ratio. If the following switches are operated during data change, the changed data will be cleared. Store the data before
changing the channel, scan size, aspect ratio or input signal format.
■ INPUT SELECT switch ■ SCAN switch ■ ASPECT switch
FUSE
ASPECT SCAN DELAY
HUE CHROMA BRIGHT CONT
MANUAL
R G B
SCREENS
PRESET
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3 CREAR
F I L E PRESET COL/MONO IN
EXT
ROTATION MK.PHASE H .CENT V . CENT SYNC SET UP
EXPAND APT MIDTH HEIGHT RE . SC
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3 F I L E CREAR PRESET COL/MONO IN
EXT
SET UP
ROTATION MK.PHASE H .CENT V . CENT SYNC
EXPAND APT MIDTH HEIGHT RE . SC
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3 F I L E CREAR PRESET COL/MONO IN
EXT
SET UP
ROTATION MK.PHASE H .CENT V . CENT SYNC
EXPAND APT MIDTH HEIGHT RE . SC
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3 F I L E CREAR PRESET COL/MONO IN
EXT
SET UP
ROTATION MK.PHASE H .CENT V . CENT SYNC
EXPAND APT MIDTH HEIGHT RE . SC
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3
F I L E CREAR PRESET COL/MONO IN
EXT
SET UP
ROTATION MK.PHASE H .CENT V . CENT SYNC
EXPAND APT MIDTH HEIGHT RE . SC
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3
F I L E CREAR PRESET COL/MONO IN
EXT
SET UP
ROTATION MK.PHASE H .CENT V . CENT SYNC
EXPAND APT MIDTH HEIGHT RE . SC
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3 F I L E CREAR PRESET COL/MONO IN
EXT
ROTATION MK.PHASE H .CENT V . CENT SYNC SET UP
EXPAND APT MIDTH HEIGHT RE . SC
F I L E S TO R E CHANGE FORCED MATRIX
1 2 3 CREAR
F I L E PRESET COL/MONO IN
EXT
ROTATION MK.PHASE H .CENT V . CENT SYNC SET UP
EXPAND APT MIDTH HEIGHT RE . SC
Set the SCAN size to the UNDER SCAN mode using the SCAN
switch, and display the 10-division crosshatch marker using the
HTM-1917R
FILE
MARKER switch.
COLOR MONITOR
1
2
3
Press the CHANGE PRESET switch, and each PRESET switch
starts to blink.
<Changing the screen phase>
Set the MK.PHASE switch to ON. Change the phase using the
encoder so that the screen fits inside the marker frame.
<Changing the centering>
Set the H.CENT switch to ON, and move the horizontal position
of the screen to the center using the encoder.
Use the V.CENT switch for vertical direction.
<Changing the size>
Set the WIDTH switch to ON, and change the amplitude size of the
screen using the encoder.
Use the HEIGHT switch to change the screen height.
<Changing the trapezoid distortion>
Set the EXPAND switch to ON and change the trapezoid distortion
using the encoder.
<Changing the side pin>
Set the EXPAND switch to ON again.
The SIDE PIN mode is set. Change the side pin using the encoder.
<Storing data>
After changing the data, press the CHANGE PRESET switch to
store the new data.
<Clearing data>
Before storing the above data, pressing the CLEAR switch will
clear all changes and restores the previous data.
24