BRP Sea-Doo GTX PRO 130 Operator's Manual page 69

N N O O T T E E : :
A minimum of 25% of iBR lever stroke
is required to activate iBR functions.
T T Y Y P P I I C C A A L L
1. Lever rest position
2. 25% stroke required to activate iBR
functions
At speed above 14 km/h (9 MPH),
pulling the iBR lever will engage the
brake.
N N O O T T E E : :
If water current is 14 km/h (9 MPH) or
above, the reverse can not be en-
gaged as the speed threshold for the
reverse is exceeded.
At speed below 14 km/h (9 MPH), pull-
ing the iBR lever will engage reverse.
When the iBR lever is released after
braking or reverse operation, the neu-
tral is engaged.
W W A A R R N N I I N N G G
I I f f t t h h r r o o t t t t l l e e l l e e v v e e r r i i s s s s t t i i l l l l p p u u l l l l e e d d i i n n
w w h h e e n n r r e e l l e e a a s s i i n n g g t t h h e e i i B B R R l l e e v v e e r r , , f f o o r r - -
w w a a r r d d m m o o v v e e m m e e n n t t w w i i l l l l b b e e i i n n i i t t i i a a t t e e d d
a a f f t t e e r r a a s s h h o o r r t t d d e e l l a a y y . . I I f f f f o o r r w w a a r r d d a a c c - -
c c e e l l e e r r a a t t i i o o n n i i s s n n o o t t d d e e s s i i r r e e d d , , r r e e l l e e a a s s e e
t t h h e e t t h h r r o o t t t t l l e e l l e e v v e e r r . .
N N O O T T E E : :
The neutral position can be fine tuned
by trimming the iBR system.
Refer to Operating Instructions for de-
tailed instructions.
E E n n g g i i n n e e C C u u t t - - O O f f f f S S w w i i t t c c h h
The engine cut-off switch is located in
the middle of the handlebar.
T T Y Y P P I I C C A A L L
To allow engine starting, the tether
cord cap must be securely snapped to
the engine cut-off switch.
W W A A R R N N I I N N G G
A A l l w w a a y y s s a a t t t t a a c c h h t t h h e e t t e e t t h h e e r r c c o o r r d d c c l l i i p p
t t o o t t h h e e o o p p e e r r a a t t o o r r ' ' s s p p e e r r s s o o n n a a l l f f l l o o t t a a - -
t t i i o o n n d d e e v v i i c c e e ( ( P P F F D D ) ) o o r r w w r r i i s s t t ( ( w w r r i i s s t t
s s t t r r a a p p r r e e q q u u i i r r e e d d ) ) . .
T T Y Y P P I I C C A A L L
1. Tether cord cap on the engine cut-off switch
2. Tether cord secured to operator's PFD
To stop engine, pull the tether cord
cap from the engine cut-off switch.
W W A A R R N N I I N N G G
S S h h o o u u l l d d t t h h e e e e n n g g i i n n e e b b e e s s t t o o p p p p e e d d , , t t h h e e
b b r r a a k k e e f f u u n n c c t t i i o o n n a a n n d d a a l l l l w w a a t t e e r r c c r r a a f f t t
d d i i r r e e c c t t i i o o n n a a l l c c o o n n t t r r o o l l i i s s l l o o s s t t . .
CONTROLS
67