BRP Sea-Doo GTX PRO 130 Operator's Manual page 100

SPECIAL PROCEDURES
T T Y Y P P I I C C A A L L
3. If equipped, move the iBR to the
forward position. Refer to iBR
Override Function for detailed
instructions.
4. Clean the water intake area.
If the system is still clogged, refer
to an authorized Sea-Doo dealer
for servicing.
N N O O T T I I C C E E
I I n n s s p p e e c c t t w w a a t t e e r r i i n n t t a a k k e e g g r r a a t t e e f f o o r r
d d a a m m a a g g e e . . R R e e f f e e r r t t o o a a n n a a u u t t h h o o r r i i z z e e d d
S S e e a a - - D D o o o o d d e e a a l l e e r r f f o o r r r r e e p p a a i i r r a a s s
n n e e c c e e s s s s a a r r y y . .
i i B B R R O O v v e e r r r r i i d d e e F F u u n n c c t t i i o o n n
When the iBR override function is acti-
vated, it allows the user to electrically
move the iBR gate and nozzle through
its full range of motion using the VTS
control button.
N N O O T T E E : :
The iBR override function is only avail-
able when the engine is not running.
W W A A R R N N I I N N G G
W W h h e e n n m m o o v v i i n n g g t t h h e e i i B B R R g g a a t t e e u u s s i i n n g g
t t h h e e i i B B R R o o v v e e r r r r i i d d e e f f u u n n c c t t i i o o n n , , e e n n s s u u r r e e
n n o o o o n n e e i i s s n n e e a a r r t t h h e e r r e e a a r r o o f f t t h h e e
w w a a t t e e r r c c r r a a f f t t . . M M o o v v e e m m e e n n t t o o f f t t h h e e g g a a t t e e
m m a a y y s s q q u u e e e e z z e e f f i i n n g g e e r r s s . .
98
N N O O T T I I C C E E
A A n n o o b b j j e e c c t t o o r r t t o o o o l l c c a a u u g g h h t t i i n n t t h h e e i i B B R R
s s y y s s t t e e m m w w h h e e n n u u s s i i n n g g t t h h e e i i B B R R o o v v e e r r - -
r r i i d d e e f f u u n n c c t t i i o o n n m m a a y y c c a a u u s s e e d d a a m m a a g g e e
t t o o t t h h e e i i B B R R c c o o m m p p o o n n e e n n t t s s . . R R e e m m o o v v e e
a a l l l l r r i i g g i i d d f f o o r r e e i i g g n n o o b b j j e e c c t t s s t t h h a a t t m m a a y y
o o b b s s t t r r u u c c t t t t h h e e i i B B R R g g a a t t e e t t r r a a v v e e l l b b e e f f o o r r e e
m m o o v v i i n n g g i i t t . .
W W A A R R N N I I N N G G
I I f f i i t t i i s s n n e e c c e e s s s s a a r r y y t t o o r r e e a a c c h h i i n n t t o o r r e e - -
m m o o v v e e a a n n y y f f o o r r e e i i g g n n o o b b j j e e c c t t c c a a u u g g h h t t i i n n
t t h h e e p p r r o o p p u u l l s s i i o o n n s s y y s s t t e e m m , , s s t t r r i i c c t t l l y y o o b b - -
s s e e r r v v e e t t h h e e f f o o l l l l o o w w i i n n g g b b e e f f o o r r e e
p p r r o o c c e e e e d d i i n n g g : :
– – R R e e m m o o v v e e t t e e t t h h e e r r c c o o r r d d f f r r o o m m t t h h e e
e e n n g g i i n n e e c c u u t t - - o o f f f f s s w w i i t t c c h h . .
– – W W a a i i t t a a t t l l e e a a s s t t 5 5 m m i i n n u u t t e e s s . .
– – D D o o n n o o t t p p r r e e s s s s o o n n S S T T A A R R T T / / S S T T O O P P
b b u u t t t t o o n n . . S S h h o o u u l l d d t t h h e e S S T T A A R R T T / /
S S T T O O P P b b u u t t t t o o n n b b e e p p r r e e s s s s e e d d , , w w a a i i t t
a a n n o o t t h h e e r r 5 5 m m i i n n u u t t e e s s . .
A A c c t t i i v v a a t t i i n n g g i i B B R R O O v v e e r r r r i i d d e e F F u u n n c c t t i i o o n n
1. Power up the electrical system by
pressing the START/STOP button.
2. Install the tether cord on the en-
gine cut-off switch.
N N O O T T E E : : The tether cord must be in-
stalled to ensure the information cen-
ter will not shut off all indications after
its self test function. Electrical power
will stay on for approximately 1 hour.
3. Pull in and hold the iBR lever for
the entire procedure.