BRP Sea-Doo GTX PRO 130 Operator's Manual page 70

CONTROLS
W W A A R R N N I I N N G G
A A l l w w a a y y s s d d i i s s c c o o n n n n e e c c t t t t e e t t h h e e r r c c o o r r d d
w w h h e e n n w w a a t t e e r r c c r r a a f f t t i i s s n n o o t t i i n n o o p p e e r r a a - -
t t i i o o n n i i n n o o r r d d e e r r t t o o p p r r e e v v e e n n t t a a c c c c i i d d e e n n t t a a l l
e e n n g g i i n n e e s s t t a a r r t t i i n n g g o o r r t t o o a a v v o o i i d d u u n n a a u u - -
t t h h o o r r i i z z e e d d u u s s e e b b y y o o t t h h e e r r s s , , c c h h i i l l d d r r e e n n , ,
a a n n d d t t o o p p r r e e v v e e n n t t t t h h e e f f t t . .
R R a a d d i i o o F F r r e e q q u u e e n n c c y y D D i i g g i i t t a a l l l l y y E E n n c c o o d d e e d d
S S e e c c u u r r i i t t y y S S y y s s t t e e m m ( ( R R F F D D . . E E . . S S . . S S . . ) )
The tether cord cap contains an elec-
tronic circuit (D. E. S. S.™ key) that is
programmed to give it a unique elec-
tronic serial number. This is the equiv-
alent of a conventional key.
The D.E.S.S. system reads the key in-
stalled on the engine cut-off switch
and only allows engine starting for
keys it recognizes.
The D.E.S.S. system brings great flex-
ibility. You can buy additional tether
cords and have the D.E.S.S. keys pro-
grammed for your watercraft.
A total of ten D. E. S. S. keys can be
programmed.
To have a key programmed to your
watercraft, see your authorized BRP
Sea-Doo dealer.
E E n n g g i i n n e e S S T T A A R R T T / / S S T T O O P P B B u u t t t t o o n n
The engine START/STOP button is lo-
cated on the LH handlebar.
T T Y Y P P I I C C A A L L – – E E N N G G I I N N E E
B B U U T T T T O O N N
68
S S T T A A R R T T / / S S T T O O P P
E E n n g g i i n n e e S S t t a a r r t t i i n n g g a a n n d d S S t t o o p p p p i i n n g g
Refer to Operating Instructions for
complete procedures on how to start
and stop the engine.
W W a a k k i i n n g g U U p p t t h h e e E E l l e e c c t t r r i i c c a a l l S S y y s s t t e e m m
Press the START/STOP button once
without installing the tether cord on
the engine cut-off switch.
This will power up the electrical sys-
tem; the information center will cycle
through a self-test function.
The electrical system will stay pow-
ered up for approximately 75 seconds
after the START/STOP button was
depressed.
When the tether cord is installed on
the engine cut-off switch, the system
will be powered for 60 minutes.
Every time the START/STOP button is
pressed, the
When the battery voltage drops below
12.3V, the LOW BATTERY indicator
lamp will light up and the electrical
system will shut down after 75
seconds.
P P o o s s t t - - D D r r i i v v e e B B a a t t t t e e r r y y M M a a n n a a g g e e m m e e n n t t
This feature allows keeping the elec-
trical system awake to allow using ac-
cessories when the engine is turned
off. It also prevents draining the bat-
tery too much when using accesso-
ries. When the
reaches 12.3V or less, the system will
automatically shut down to ensure
being able to start the engine.
When the electrical system is acti-
vated by pressing start-stop briefly
while the engine is shutdown the
wake-up time will be managed as
follows:
– Key off: System will shut down
after 75 seconds.
– Key on: System will shut down
after 60 minutes or if the voltage
threshold is reached.
countdown restarts.
battery voltage