BRP Sea-Doo GTX PRO 130 Operator's Manual page 114

MAINTENANCE PROCEDURES
C C A A U U T T I I O O N N
W W h h e e n n o o p p e e r r a a t t i i n n g g t t h h e e e e n n g g i i n n e e w w h h i i l l e e
t t h h e e w w a a t t e e r r c c r r a a f f t t i i s s o o u u t t o o f f w w a a t t e e r r , , t t h h e e
h h e e a a t t e e x x c c h h a a n n g g e e r r i i n n t t h h e e r r i i d d e e p p l l a a t t e e
m m a a y y b b e e c c o o m m e e v v e e r r y y h h o o t t . . A A v v o o i i d d a a n n y y
c c o o n n t t a a c c t t w w i i t t h h t t h h e e r r i i d d e e p p l l a a t t e e a a s s
b b u u r r n n s s m m a a y y o o c c c c u u r r . .
1. Raise trailer tow pole, then block in
position when bumper rail is level.
2. Install a garden hose on the ex-
haust system flushing connector.
Refer to Exhaust System in this
section and follow the procedure.
N N O O T T I I C C E E
N N e e v v e e r r r r u u n n e e n n g g i i n n e e w w i i t t h h o o u u t t s s u u p p p p l l y y - -
i i n n g g w w a a t t e e r r t t o o t t h h e e e e x x h h a a u u s s t t s s y y s s t t e e m m . .
F F a a i i l l u u r r e e t t o o c c o o o o l l e e x x h h a a u u s s t t s s y y s s t t e e m m
m m a a y y s s e e v v e e r r e e l l y y d d a a m m a a g g e e i i t t . . N N e e v v e e r r r r u u n n
e e n n g g i i n n e e l l o o n n g g e e r r t t h h a a n n 2 2 m m i i n n u u t t e e s s . .
D D r r i i v v e e l l i i n n e e s s e e a a l l h h a a s s n n o o c c o o o o l l i i n n g g
w w h h e e n n w w a a t t e e r r c c r r a a f f t t i i s s o o u u t t o o f f w w a a t t e e r r . .
3. Remove the seat(s).
4. Start the engine.
5. Open the water tap.
6. Run the COLD engine at i i d d l l e e f f o o r r
3 3 0 0 s s e e c c o o n n d d s s .
7. Close water tap.
8. Bring engine RPM to 4000-4500
RPM for 15 seconds.
9. Stop the engine abruptly by press-
ing the start/stop button or remov-
ing the tether cord.
10. Wait at least 30 seconds for the oil
to settle in the engine, then pull
dipstick out and wipe clean.
112
T T Y Y P P I I C C A A L L
1. Oil dipstick
2. Oil filler cap
11. Reinstall
completely.
12. Remove dipstick again and read
oil level. It should be between the
FULL and ADD marks.
T T Y Y P P I I C C A A L L
1. Full
2. Add
3. Operating range
13. Add oil to ensure the level is be-
tween marks as required.
1. Remove oil cap.
2. Place a funnel in valve cover
opening.
3. Add a small amount of the rec-
ommended oil to reach the
proper level.
N N O O T T I I C C E E
D D o o n n o o t t o o v v e e r r f f i i l l l l . .
dipstick, push in