BRP Sea-Doo GTX PRO 130 Operator's Manual page 126

STORAGE AND PRESEASON PREPARATION
need to add water to adjust electrolyte
level.
N N O O T T I I C C E E
N N e e v v e e r r r r e e m m o o v v e e t t h h e e b b a a t t t t e e r r y y s s t t r r i i p p
f f r r o o m m c c a a p p s s o o r r a a d d d d e e l l e e c c t t r r o o l l y y t t e e f f o o r r
t t h h e e l l i i f f e e o o f f t t h h e e b b a a t t t t e e r r y y . .
R R e e m m o o v v i i n n g g t t h h e e B B a a t t t t e e r r y y
1. Remove the seat.
2. Disconnect the battery cables.
N N O O T T I I C C E E
A A l l w w a a y y s s d d i i s s c c o o n n n n e e c c t t t t h h e e B B L L A A C C K K ( ( - - ) )
c c a a b b l l e e f f i i r r s s t t , , t t h h e e n n t t h h e e R R E E D D ( ( + + ) )
c c a a b b l l e e . .
1. Battery post
2. Strap
3. Remove the retaining strap.
C C h h a a r r g g i i n n g g t t h h e e B B a a t t t t e e r r y y
Use any automotive type battery
charger. Always refer to the battery
charger manufacturer's instructions.
C C l l e e a a n n i i n n g g t t h h e e B B a a t t t t e e r r y y
Clean battery casing and battery
posts using a soft brush and a solution
of baking soda and water.
Remove corrosion from battery cable
terminals and battery posts using a
firm wire brush.
Rinse with clear water then dry well.
I I n n s s t t a a l l l l i i n n g g t t h h e e B B a a t t t t e e r r y y
1. Connect the battery cables.
124
N N O O T T E E : : Remove any water or debris
if present in the compartment before
installing the battery.
N N O O T T I I C C E E
R R e e v v e e r r s s e e d d b b a a t t t t e e r r y y p p o o l l a a r r i i t t y y w w i i l l l l
d d a a m m a a g g e e t t h h e e v v o o l l t t a a g g e e r r e e g g u u l l a a t t o o r r . .
N N O O T T I I C C E E
A A l l w w a a y y s s c c o o n n n n e e c c t t t t h h e e R R E E D D ( ( + + ) ) c c a a b b l l e e
f f i i r r s s t t , , t t h h e e n n t t h h e e B B L L A A C C K K ( ( - - ) ) c c a a b b l l e e . .
2. Tighten the battery cable screws to
specification.
T T i i g g h h t t e e n n i i n n g g T T o o r r q q u u e e
Battery
cable screw
3. Apply dielectric grease on battery
posts.
4. Cover positive battery post with
rubber boot.
5. Verify cable
attachments.
E E n n g g i i n n e e C C o o m m p p a a r r t t m m e e n n t t
C C l l e e a a n n i i n n g g t t h h e e E E n n g g i i n n e e C C o o m m p p a a r r t t m m e e n n t t
1. Clean the bilge with hot water and
detergent or with bilge cleaner.
2. Rinse thoroughly.
3. Lift front end of watercraft to com-
pletely drain bilge through the bilge
drain plugs.
A A n n t t i i c c o o r r r r o o s s i i o o n n T T r r e e a a t t m m e e n n t t
1. Wipe off any residual water in the
engine compartment.
2. Lubricate all metallic components
in engine compartment.
4 ± 0.5 Nm
(35 ± 4 lbf-in)
routing and