BRP Sea-Doo GTX PRO 130 Operator's Manual page 101

1. iBR lever pulled and held
4. When the I I B B R R O O V V E E R R R R I I D D E E - -
P P R R E E S S S S M M O O D D E E B B U U T T T T O O N N mes-
sage appears in the multifunction
gauge, press the MODE button.
When the function is activated, a
ON message will be shown.
5. While still holding the iBR lever in,
press the VTS UP/DOWN button
to move the iBR gate to the de-
sired position. Ensure the VTS in-
dication in the multifunction gauge
changes with the iBR gate move-
ment. If the iBR gate moves up-
wards, the
upwards.
6. Release the iBR lever.
7. Remove the tether cord from the
engine cut-off switch.
W W A A R R N N I I N N G G
I I f f i i t t i i s s n n e e c c e e s s s s a a r r y y t t o o r r e e a a c c h h i i n n t t o o r r e e - -
m m o o v v e e a a n n y y f f o o r r e e i i g g n n o o b b j j e e c c t t c c a a u u g g h h t t i i n n
t t h h e e p p r r o o p p u u l l s s i i o o n n s s y y s s t t e e m m , , s s t t r r i i c c t t l l y y o o b b - -
s s e e r r v v e e t t h h e e f f o o l l l l o o w w i i n n g g b b e e f f o o r r e e
p p r r o o c c e e e e d d i i n n g g : :
– – R R e e m m o o v v e e t t e e t t h h e e r r c c o o r r d d f f r r o o m m t t h h e e
e e n n g g i i n n e e c c u u t t - - o o f f f f s s w w i i t t c c h h . .
– – W W a a i i t t a a t t l l e e a a s s t t 5 5 m m i i n n u u t t e e s s . .
– – D D o o n n o o t t p p r r e e s s s s o o n n S S T T A A R R T T / / S S T T O O P P
b b u u t t t t o o n n . . S S h h o o u u l l d d t t h h e e S S T T A A R R T T / /
S S T T O O P P b b u u t t t t o o n n b b e e p p r r e e s s s s e e d d , , w w a a i i t t
a a n n o o t t h h e e r r 5 5 m m i i n n u u t t e e s s . .
indication moves
C C a a p p s s i i z z e e d d W W a a t t e e r r c c r r a a f f t t
The watercraft is designed so that it
should not turn over easily. Two spon-
sons mounted on the side of the hull
assist watercraft stability. If it turns
over, it will remain capsized.
To turn the watercraft upright, ensure
the engine is off and the D.E.S.S. key
is N N O O T T on its post, then grab the inlet
grate, step on a side bumper rail and
use your weight to rotate the water-
craft towards you.
N N O O T T E E : :
A label on the stern near the flushing
connector provides instructions on
how to turn the watercraft right side
up. The label is upside down so that it
can be read when the watercraft is
overturned.
T T Y Y P P I I C C A A L L
The engine features a Tip-Over Pro-
tection System (T. O. P. S.™). When
the watercraft tips over, the engine is
automatically stopped.
When the watercraft is returned to its
normal operating position, the engine
can be started normally.
SPECIAL PROCEDURES
99