Section 3 - Definitions; Additional Safety Symbol Definitions; Miscellaneous Symbol Definitions - Miller Trailblazer 325 Diesel Owner's Manual

3-1.

Additional Safety Symbol Definitions

�
Some symbols are found only on CE products.
3-2.

Miscellaneous Symbol Definitions

Do not use ether or other starting fluids. Using starting fluids voids warranty. See engine Owner's Manual.
Do not use ether or other starting fluids. Using starting fluids voids warranty. See engine Owner's Manual.
Amperage
Hot muffler and exhaust pipe can cause severe burns.
Voltage
Hot muffler and exhaust pipe can cause severe burns.
Welding, cutting, drilling, or grinding on base can cause fire or explosion.
Welding, cutting, drilling, or grinding on base can cause fire or explosion.
Duty Cycle
Do not spray water on CST units.
Do not spray water on CST units.
Seconds
Rated No-Load Volt-
age (OCV)
Door must be fully open during operation.
Door must be fully open during operation.
Conventional Load
Voltage
Drive rolls can injure fingers. Welding wire and drive parts are at welding voltage during operation
Drive rolls can injure fingers. Welding wire and drive parts are at welding voltage during operation
and metal objects away.
and metal objects away.
�
Complete Parts List is available at www.MillerWelds.com
SECTION 3 – DEFINITIONS
Falling unit can cause injury and damage. Do not move unit where two wheels are at a different height and un
could tip avoid tipping. Be careful when moving unit over uneven surfaces.
Do not stack racks. Lift only with proper equipment and correct procedures.
Do not use ether or other starting fluids. Using starting fluids voids warranty. See engine Owner's Manual.
Moving parts can injure.
Hot muffler and exhaust pipe can cause severe burns.
Always connect green, Or green with yellow stripe, wire to supply grounding terminal.
Connect black, white, and red wires (L1, L2, L3) to line terminals.
Welding, cutting, drilling, or grinding on base can cause fire or explosion.
Pinch points can injure.
Do not spray water on CST units.
Recycle.
Door must be fully open during operation.
Become trained and read the instructions before working on machine.
Drive rolls can injure fingers. Welding wire and drive parts are at welding voltage during operation
and metal objects away.
Hertz
Connect green or green/yellow grounding conductor to ground terminal.
Hours
For single phase operation, insulate and isolate red conducto
Include extra length in grounding conductor and connect grou
conductor first. Connect black, white, and red wires (L1, L2, L
Never use generator inside a home or garage, even if doors a
line terminals.
dows are open.
Only use generator outside and far away from windows, doo
vents.
Warning! Watch Out! There are possible hazards as shown by the
symbols.
Become trained and read the instructions before working on the
Become trained and read the instructions before working on the
Do not use ether or other starting fluids. Using starting fluids voids
machine or heating.
machine or heating.
warranty. See engine Owner's Manual.
Connect green or green/yellow grounding conductor to ground
Connect green or green/yellow grounding conductor to ground
Moving parts can injure.
terminal.
terminal.
Connect input conductors (L1, L2 And L3) to line terminals.
Connect input conductors (L1, L2 And L3) to line terminals.
Never use generator inside a home or garage, even if doors and win- Never use generator inside a home or garage, even if doors and win-
Never use generator inside a home or garage, even if doors and win-
dows are open. dows are open.
dows are open.
Only use generator outside and far away from windows, doors, and
Only use generator outside and far away from windows, doors, and
Only use generator outside and far away from windows, doors, and vents.
vents.
vents.
Rated Welding
Current
Negative
Positive
Direct Current (DC)
Alternating Current
Connect input conductors (L1, L2 And L3) to line terminals.
(AC)
Protective Earth
(Ground)
Circuit Breaker
Supplementary
Protector
Output
Safe8
Safe87
Safe88
Safe85 2012 06
Safe85 2012 06
Safe1
Safe86 2012 06
Safe86 2012 06
Safe87 2012 07 Safe1
Safe87 2012 07
Safe1
Safe88 2012 07
Safe88 2012 07
Safe1
Read Operator's
Safe89 2017 04
Safe89 2017 04
Manual
Shielded Metal Arc
Welding (SMAW)
keep han
Safe1
Safe90 2017 04
Safe90 2017 04
Gas Metal Arc
Welding (GMAW)
Flux Cored Arc
Safe1
Welding (FCAW)
Safe91 2017 04
Safe91 2017 04
Gas Tungsten Arc
Welding (GTAW)/
Tungsten Inert Gas
(TIG) Welding
Safe 1
Touch Start (GTAW)
Safe92 2017 04
Safe92 2017 04
Clock, Time Switch
Safe93 2012 08
Safe93 2012 08
Engine Oil
keep hands
OM-279836 Page 15
keep hands
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe