Setting Password; Setting Speeds 1-8; Pump Operating Modes - Pentair INTELLIFLOXF Installation And User Manual

10
MENU
Pump Menu: Settings
SETTINGS Pump Address

Setting Password

1. Check that the green power LED is on.
2. Press Menu. Press Select to select "Settings".
Temperature Unit
3. Use the Up or Down arrow to scroll to "Device".
4. Press Select.
Screen Contrast
5. Press Up or Down arrow to scroll to "Password". The
default setting is "Disabled".
Set Min Speed
6. Press Select.
7. Press Up or Down arrow to change the setting to
Set Max Speed
"Enabled". Press Save to save.
PASSWORD
8. Press the Down arrow. "Password Timeout" will be
displayed. The factory default time is 1 minute. This
means the pump will go into Password Protection
mode 1 minute after the last control panel key is
pressed.
9. Press Select to change time setting from 1 minute to
6 hours and press Save to save.
10. Press the Down arrow and then press Select on
"Enter Password" to change the setting.
11. Press the Left or Right arrows to move cursor and
press the Up or Down arrow to change the password
number to desired setting.
12. Press Save to save. To cancel any changes, press
Back to exit without saving.
Entering Password
1. Press any button (besides a Speed button) to prompt
the screen for a password.
2. To enter password, use the Left and Right arrows
to move the cursor and the Up and Down arrows to
scroll through the digit then press Save to confirm.
XF
®
INTELLIFLO and INTELLIPRO
(1-16) Default: ADDRESS 1
Set Time
(hr:mm) Default: 12:00 AM
AM/PM
Set AM/PM
24 hr.
Fahrenheit - Default: F°
C° Celsius
(1-5) Default 3
English - Default: English
Language
(450 RPM - 1700 RPM) - Default: 450 RPM
(1900 RPM - 3450 RPM) - Default: 3450 RPM
Disabled/Enabled - Default: Disabled
Password Time Out (1 min. - 6 hours) Default:10 minutes
Enter Password (xxxx) Default: 1234
XF
®
Variable Speed Pump Installation and User' s Guide
MENU
Pump Menu: Speeds 1-8
SPEED 1-8

Pump Operating Modes

The pump can be programmed in three different modes:
Manual, Schedule, and Egg Timer: Speeds 1-4 can be
programmed in all three modes. Speeds 5-8 can only
be programmed in Schedule mode since there are no
buttons on the control panel for Speeds 5-8. The default
setting for Speeds 5-8 is "Disabled".
Speed 1 (1-4)
Egg Timer
Speed 5 (5-8)
Speed Menu Tree Options
Manual
Assigns a speed to one of the four Speed buttons on the
control panel. This mode can only be used for speeds
1-4.
To operate in Manual mode, press one of the four speed
buttons and then press the Start/Stop button. The pump
will run the assigned speed for that speed button.
Egg Timer
Speeds 1-4 can be programmed to run at a certain
speed and for a duration of time once a speed button is
pressed.
Speeds 3 and 4 are Egg Timers by default. This prevents
the pump from running at a speed higher than half of
the maximum speed indefinitely. If you desire a different
method of operation, speeds 3 and 4 can be changed to
Manual mode in the control menu.
To operate in Egg Timer mode, press a speed button and
then press Start/Stop. The pump will run that speed for
the set amount of time and then turn off.
Schedule
Program speeds 1-8 start and stop at a specific time
during a 24 hour period. Speeds programmed in
Schedule mode will override any manually selected
speed (speeds set by manually pressing any of the
speed buttons on the control panel).
Manual
Speed 1 (1-4)
Schedule
Egg Timer
Disabled
Speed 5 (5-8)
Schedule
Manual
Set Speed - Default: MANUAL
Schedule
Set Speed
Set Start Time
Set Stop Time
Set Speed
Time
Disabled
Default: Disabled
Schedule
Set Speed
Set Start Time
Set Stop Time
Set Speed
Set Speed
Set Start T
Set Stop T
Set Speed
Time
Default: Di
Set Speed
Set Start Ti
Set Stop Ti