Setting Password; Setting Speeds 1-8; Pump Operating Modes - Pentair IntelliFlo Installation And User Manual

MENU
Pump Menu: Settings
SETTINGS

Setting Password

1. Check that the green power LED is on.
2. Press Menu. Press Select to select "Settings".
Temperature Unit
3. Use the Up or Down arrow to scroll to "Device".
4. Press Select.
Screen Contrast
5. Press Up or Down arrow to scroll to "Password". The
default setting is "Disabled".
6. Press Select.
7. Press Up or Down arrow to change the setting to
"Enabled". Press Save to save.
8. Press the Down arrow. "Password Timeout" will be
displayed. The factory default time is 1 minute. This
means the IntelliFlo
®
into Password Protection mode 1 minute after the
last control panel key is pressed.
9. Press Select to change time setting from 1 minute
to 6 hours and press Save to save.
10. Press the Down arrow and then press Select on
"Enter Password" to change the setting.
11. Press the Left or Right arrows to move cursor and
press the Up or Down arrow to change the password
number to desired setting.
12. Press Save to save. To cancel any changes, press
Back to exit without saving.
Entering Password
1. Press any button (besides the speed button) to prompt
the screen for a password.
2. To enter password, use the Left and Right arrows to
move the cursor and the Up and Down arrow button
to scroll through the digit then press Save to confirm.
Pump Address (1-16) Default: ADDRESS 1
Set Time
(hr:mm) Default: 12:00 AM
AM/PM
Set AM/PM
24 hr.
Fahrenheit - Default: F°
C° Celsius
(1-5) Default 3
English - Default: English
Language
Set Min Speed
(450 RPM - 1700 RPM) - Default: 450 RPM
Set Max Speed (1900 RPM - 3450 RPM) - Default: 3450 RPM
PASSWORD Disabled/Enabled - Default: Disabled
Password Time Out (1 min. - 6 hours) Default:10 minutes
Enter Password (xxxx) Default: 1234
Variable Speed Pump will go
MENU
SPEED 1-8

Pump Operating Modes

The IntelliFlo Variable Speed Pump can be pro-
®
grammed in three different modes:
Manual, Schedule, and Egg Timer. Speeds 1-4 can
be programmed in all three modes. Speeds 5-8 can
only be programmed in Schedule mode since there are
no buttons on the control panel for Speeds 5-8. The
default setting for Speeds 5-8 is "Disabled".
Speed 1 (1-4)
Speed 5 (5-8)
Speed Menu Tree Options
Manual
Assigns a speed to one of the four Speed buttons
on the control panel. This mode can only be used for
speeds 1-4.
To operate in Manual mode, press one of the four
speed buttons and then press the Start/Stop button.
The pump will run the assigned speed for that speed
button.
Egg Timer
Speeds 1-4 can be programmed to run at a certain
speed and for a duration of time once a speed button
is pressed.
Speeds 3 and 4 are Egg Timers by default. If you
desire a different method of operation, speeds 3 and 4
can be changed to Manual mode in the control menu.
To operate in Egg Timer mode, press a speed but-
ton and then press Start/Stop. The pump will run that
speed for the set amount of time and then turn off.
Schedule
Program speeds 1-8 start and stop at a specific time
during a 24 hour period. Speeds programmed in
Schedule mode will override any manually selected
speed (speeds set by manually pressing any of the
speed buttons on the control panel).
INTELLIFLO Variable Speed Pump Installation and User's Guide
®
Pump Menu: Speeds 1-8
Manual
Speed 1 (1-4)
Schedule
Egg Timer
Disabled
Speed 5 (5-8)
Schedule
Manual
Set Speed - Default: MANUAL
Schedule
Set Speed
Set Start Time
Set Stop Time
Egg Timer
Set Speed
Time
Disabled
Default: Disabled
Schedule
Set Speed
Set Start Time
Set Stop Time
11
Set Spee
Set Spee
Set Start
Set Stop
Set Spee
Time
Default:
Set Spee
Set Start
Set Stop