Table of Contents
Advertisement
INSTALLATION CHECKLIST
1) Locate appliance. Refer to the following sections:
a) Locating Your Gas Fireplace
b) Clearances
c) Combustible Mantel Clearances
d) Framing & Finishing
e) Venting
2) Assemble Top Standoffs and Top Facing
Support and Side Nailing Strips (Refer to the
"Unit Assembly Prior to Installation" section).
NOTE: Must be done before installing unit into
fireplace.
3) Install vent (Refer to the "Venting" sections).
4) Wire 120 volt AC power to the supplied receptacle
box located on the lower lefthand side of the
appliance. The Duplex receptacle and receptacle
cover are included in the manual package.
This heater requires 120 volt AC supply
for optional blower operation.
5) Install the junction box supplied with the
appliance. Install the remote receiver inside
the junction box. Hook the receiver to the wire
marked "receiver". Install 4 AA batteries inside
the receiver to enable operation of the burner.
Note: If optional fan is not purchased, batteries
are required in both remote receiver (4 x AA
batteries) & remote hand held (3 x AAA batteries)
in order to operate appliance using the remote
control.
6) Make gas connections. Test the pilot. Must be
as per the diagram in the "Pilot Adjustment"
section.
Convert to propane if desired (Refer to the
"Conversion from NG to LP" section).
7) Install standard and optional features. Refer
to the following sections where applicable:
a. Code the remote supplied with the unit.
b. Optional brick panels/enamel panels.
c. Log set installation.
d. Standard flush door.
e. Vignette faceplate/vignette finishing trim.
f. Louvers & safety screen.
g. Optional wall thermostat.
h. Optional fan installation.
8) Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to
customer.
This includes:
1) Clocking the appliance to ensure the correct
firing rate (rate noted on label 30,000 Btu/h)
after burning appliance for 15 minutes.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
CAUTION:
Any alteration to the product that causes
sooting or carboning that results in damage
is not the responsibility of the manufacturer.
LOCATING YOUR
GAS FIREPLACE
1) When selecting a location for your fireplace,
ensure that the clearances outlined on this
page are met.
2) Provide adequate clearances for servicing.
3) The appliance must be installed on a flat, solid,
continuous surface (e.g. wood, metal, concrete).
This may be the floor, or raised up on a platform
to enhance its visual impact. If the appliance is
going to be installed on carpeting, combustible
linoleum tile or other combustible material other
than wood flooring, the appliance must be
installed on a metal or wood panel extending
the full width and depth of the appliance.
4) The P36 Direct Vent Gas Fireplace can be
installed in a recessed position or framed out
into the room as in A, B, C, D. See
Diagram 1.
Diagram 1
A) Flat on Wall
B) Flat on Wall Corner
C) Recessed into Wall/Alcove
D) Corner
5) This appliance is Listed for bedroom installations
when used with a Listed Millivolt Thermostat.
Some areas may have further requirements,
check local codes before installation.
6) The P36 Direct Vent Gas Fireplace is approved for
alcove installations, which meet the clearances
listed on this page.
7) We recommend that you plan your installation on
paper using exact measurements for clearances
and floor protection before actually installing this
appliance. Have a qualified inspector, dealer, or
installer review your plans before installation.
Note: For vent terminations see the "Exterior
Vent Termination Locations" section.
MANUFACTURED MOBILE
HOME ADDITIONAL
REQUIREMENTS
1) Ensure that structural members are not cut or
weakened during installation.
2) Ensure proper grounding using the #8 ground
lug provided. See the "Alternate Wiring Diagram
for Wall Switch" section.
HEATWAVE DUCT SYSTEM
OPTIONAL KIT #946-556
The HeatWave Air Duct Kit increases the
effectiveness of your fireplace by dispersing warm
air from the fireplace to remote locations in the
same room or other rooms in your home.
Up to two kits may be installed on the fireplace.
Please Note: Only 1 HeatWave kit may be oper-
ated at one time. This includes the internal blower
option as well.
The HeatWave Duct Kit has different clearance
and framing requirements, check the HeatWave
manual for details.
P36-10 Zero Clearance Direct Vent Gas Fireplace |
installation
|
17
17
Advertisement
Table of Contents
