Table of Contents
Advertisement
Quick Links
Panorama
Direct Vent Gas Fireplace
MODELS:
P33E-NG11 Natural Gas
Warning
FIre or explosion Hazard
failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Tested by:
ertified to/Certifié pour : CSA 2.17-2017
C
919-963k
P33E Zero Clearance
®
P33E-LP11 Propane
ANSI Z21.88-2019
CSA 2.33-2019
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
Installer: Please complete the details on the back
cover and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future
reference.
Owners &
Installation Manual
P33 Video
www.regency-fire.com
03.03.23
Advertisement
Table of Contents
Related Manuals for Regency Fireplace Products Panorama P33E
Summary of Contents for Regency Fireplace Products Panorama P33E
- Page 1 Panorama P33E Zero Clearance Owners & ® Installation Manual Direct Vent Gas Fireplace P33 Video www.regency-fire.com MODELS: P33E-NG11 Natural Gas P33E-LP11 Propane Warning FIre or explosion Hazard failure to follow safety warnings exactly could result in serious injury, death, or property damage. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Page 2 To the New Owner: Congratulations! You are the owner of a state-of-the-art Gas Fireplace by FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. The P33E- 11 has been designed to provide you with all the warmth and charm of a wood fireplace at the flick of a switch. The P33E-11 has been approved by Warnock Hersey/Intertek for both safety and efficiency.
- Page 3 INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE This Regency product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: VENTED ® GAS FIREPLACE HEATERS ANSI Z21.88 / CSA 2.33 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CSA 2.17. This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufac- tured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.
-
Page 4: Table Of Contents
table of contents owner's installation Unit Installation with Vertical Termination......40 Gas Line Installation ............40 On Demand Pilot Light (seven day safety timer) ....4 Vertical Flue Extension Kit (Part #946-756) ...... 42 Copy of Safety Decal ............5 Ceiling Firestop/Firestop Spacer (Part #946-757) ....42 Decal location ..............5 Pilot Adjustment ............. -
Page 5: Copy Of Safety Decal
safety decal Safety Label This is a copy of the label that accompanies each P33E-11 Zero Clearance Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. The safety label is located on the front inside base of the unit, visible when the bottom louver is open. NOTE: Regency units are constantly being improved. - Page 6 requirements MA Code - CO Detector (for the State of Massachusetts only) 5.08: Modifications to NFPA-54, Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:...
-
Page 7: Unit Dimensions With Vignette
dimensions Unit Dimensions with Vignette and Vignette Finishing Trim Unit Dimensions with Safety Screen and Optional Louvers Note: Gas connection is from the right hand side of the appliance & electrical connection on left hand side of the appliance. A metal receptacle box is supplied/installed with the appliance to make all 120 volt electrical connections. -
Page 8: Gas Installation Checklist
dimensions Gas Installation Checklist REGENCY GAS INSTALLATION CHECKLIST This general checklist does not contain all pertinent installation details or specifics and does not supersede the guidelines in this manual. Your Regency dealer/installer should use it in conjunction with manual instructions. Please follow all local codes and jurisdictions in authority. Customer: Date Installed: Install Address:... - Page 9 installation REGENCY GAS INSTALLATION CHECKLIST Finishing If applicable, is only noncombustible material installed in the noncombustible areas? Do clearances meet installation and manual requirements? Do the mantels and/or projections comply with the installation manual? If applicable, was the solid fuel fireplace warning plate installed? Appliance Media Setup Do commands from the remote or wall switch light the pilot and main burner? Are the burner media/log set, glass door, and screen installed per instructions in the manual?
-
Page 10: Important Message
installation 3) See general construction and assembly Important Message YOUNG CHILDREN SHOULD BE instructions. The appliance and vent should SAVE THESE CAREFULLY SUPERVISED WHEN be enclosed. INSTRUCTIONS THEY ARE IN THE SAME AREA AS THE APPLIANCE. TODDLERS, 4) This appliance must be connected to the The P33E-NG11 or P33E-LP11 Direct Vent Fireplace YOUNG CHILDREN AND OTHERS MAY specified vent and termination cap to the outside... -
Page 11: Lighting Procedure
owner's information Lighting Procedure IMPORTANT: The remote control system supplied with this appliance has 3. After approximately 4 seconds the spark ignition system will spark for 60 several options for starting/operating the appliance using the power button seconds to light the pilot. and ON/OFF key on the hand held transmitter. -
Page 12: Copy Of Lighting Plate Instructions
owner's information Copy of Lighting Plate Instructions FOR YOUR SAFETY READ BEFORE LIGHTING POUR VOTRE SÉCURITÉ – À LIRE AVANT LA MISE EN MARCHE WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. -
Page 13: Proflame I Remote Control Operating Instructions
owner's information Proflame I Remote Control Operating Instructions IMPORTANT:The Proflame Transmitter 1 is an integrated part of the TECHNICAL DATA Proflame 1 System, which consists of these elements: • Proflame 1 Transmitter, to be used in conjunction with: REMOTE CONTROL •... - Page 14 owner's information Temperature indication Display Remote - Flame Control With the system in the "OFF" position, press the Thermostat Key and the The Proflame has six (6) flame levels. With the system on, and the flame Mode Key at the same time. Look at the LCD screen on the transmitter level at the maximum in the appliance, pressing the Down Arrow Key to verify that a C or F is visible to the right of the room temperature once will reduce the flame height by one step until the flame is turned off.
- Page 15 owner's information Smart Thermostat (Transmitter Operation) Remote Dimmer Control (Light)** The auxiliary function controls the AUX power outlet by the dimmable The Smart Thermostat function adjusts the flame height in accordance light control. To activate this function use the Mode Key (fig. 1) to index to the difference between the set point temperature and the actual room to the AUX icon (fig.
- Page 16 owner's information ow Battery Power Detection Transmitter The life span of the remote control batteries depends on various factors: quality of the batteries used, the number of ignitions of the appliance, the number of changes to the room thermostat set point, etc. When the Transmitter batteries are low, a Battery Icon will appear on the LCD display of the Transmitter (Fig.
-
Page 17: Remote Receiver Battery Replacement
installation Proflame I Remote Receiver Battery Replacement & Battery Backup if 120V Power is lost within home Remote Receiver/Battery Holder Battery Replacement & Battery Back up if 120 volt If no fan control module or AC adaptor is installed, 4 AA batteries are mandatory in the remote receiver to operate the appliance when us- power is lost witihin home ing the remote control. -
Page 18: Manufactured Mobile Home Additional Requirements
installation Manufactured Mobile Home Before leaving this unit with the customer, the Flat on Wall Additional Requirements installer must ensure that the appliance is firing Flat on Wall Corner correctly and operation fully explained to Recessed into Wall/Alcove 1. Ensure that structural members are not cut or customer. -
Page 19: Clearances With Vignette Faceplate
installation Clearances with Vignette Faceplate WARNING Caution Requirements Fire hazard is an extreme risk The top, back and sides of the fireplace are defined by if these clearances (air space) to combustible materials are not standoffs. The metal ends of the standoff may NOT be adhered to. -
Page 20: Combustible Mantels
installation Combustible Mantels Because of the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from top of unit are shown in the diagram below. Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board. -
Page 21: Framing And Finishing
installation Framing and Finishing Rear Termination- Vertical Termination or Vignette and Vignette IMPORTANT FINISHING DETAIL NOTE: Before Finishing Trim - Finished Flush Vertical Rise with Horizontal placing unit into final position - it is important to know the total thickness/height of finished hearth Termination For Rigid Vent (tile, carpet, etc.). - Page 22 installation Non- combustible Rigid Vent Vignette + Vignette Finishing Trim Minimum Clearances Flush Finished Top Header 10" (254mm) 1/2" dia. Hole through (13mm) wall for Dura-Vent Drywall 1-1/2" (38mm) 4" 3" 16-1/2” (102mm) (419mm) (76mm) Minimum Opening for gas connection Flex Vent Minimum Clearances Safety Screen and Optional Louvers...
-
Page 23: Wall Mount On/Off Switch And Remote Receiver Installation
installation Wall Mount On/Off Switch and Remote Receiver Installation Required for all installations - including Proflame remote controls IMPORTANT INSTALLATION NOTE: The Receiver must be placed inside the supplied (Low Voltage) junction type wall box and installed into the wall only. DO NOT INSTALL WITHIN THE CONFINES OF THE FIREPLACE. -
Page 24: Unit Assembly Prior To Installation
installation Unit Assembly Prior to Installation NOTE: Top Facing Support & The Top Facing Support, the Side Nailing Strips and If finishing flush with the Vignette Finishing Trim - the 2 Top Standoffs must be correctly positioned Side Nailing Strips remove top nailing strip (facing support) if already and attached to the top before the unit is put into installed and use the nailing strip supplied with... -
Page 25: Exterior Vent Termination Locations
installation Exterior Vent Termination Locations Minimum Clearance Requirements Canada Clearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm) Clearance to window or door that may be opened 12"(30cm) 9" (23cm) Clearance to permanently closed window Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm) 18"(46cm) 18"(46cm) from the center line of the terminal (check with the local code) -
Page 26: Regency ® Direct Vent Flex System
installation Regency Direct Vent flex System ® Horizontal Terminations Only This venting system, in combination with the P33E-11 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey/ Intertek. The location of the termination cap must conform to the requirements in the "Exterior Vent Terminal Locations" Section. Regency Direct Vent Flex Termination Kit (Part # 946-513) includes all the parts needed to install the P33E-11 with a maximum run of 2 ®... -
Page 27: Installation Procedures
installation Installation Procedures for Regency Direct Vent System (Flex) ® 1) Locate the unit in the framing, rough in the 2) Level the fireplace and fasten it to the framing gas (preferably on the right side of the unit) using nails or screws through the nailing strips. and the electrical (Junction block is on the left side) on the left. -
Page 28: Rigid Pipe Venting Systems
installation Rigid Pipe Venting Systems Horizontal or Vertical Terminations The minimum components required for a basic horizontal termination are: AstroCap Horizontal Termination Cap Elbow Rigid Pipe Adaptor Wall Thimble Length of pipe to suit wall thickness (see chart) For siding other than vinyl furring strips may be used, instead of the vinyl siding standoff, to create a level surface to mount the vent terminal. -
Page 29: 4" X 6-5/8" Rigid Pipe Cross Reference Chart
installation 4” x 6-5/8” Rigid Pipe Cross Reference Chart Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. 4" X 6-5/8" RIGID PIPE CROSS REFERENCE CHART Note: Olympia Ventis DV is only approved for certain models. See list of approved models in cross-reference chart. Components from different Manufacturers may not be mixed. - Page 30 installation Description Simpson *Selkirk *American Metal *Metal-Fab™ *Security *ICC Excel *Olympia Direct Vent Pro ® Direct Temp™ Products® Sure Seal Secure- Vent® Direct Ventis DV*** Amerivent Direct Attic Insulation Shield 12" 46DVA-IS 4DAIS12 4DIS SV4RSA VDV-AIS04 Attic Insulation Shield 4DAIS12 TM-4AS - Cold Climates 36"...
-
Page 31: Rigid Pipe Venting Arrangements
installation Rigid Pipe Venting Arrangements Vertical Terminations (Propane & Natural Gas) elbow, with rigid The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using one 90 pipe vent systems for Propane and Natural Gas. •... - Page 32 installation The P33E-11 is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural Gas. The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations with rigid pipe vent systems for Propane and Natural Gas.
- Page 33 installation Rigid Pipe Venting Arrangements Horizontal Terminations REGENCY DIRECT VENT SYSTEM (FLEX) ® (Propane & Natural Gas) This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45 and one 90 elbow (two 45 elbows equal one elbow).
- Page 34 installation Horizontal Venting with Three (3) 90 Elbows Horizontal Venting with Two (2) 90 Elbows One 90 elbow = Two 45 elbows. One 90 elbow = Two 45 elbows. Option H + H1 With these options, maximum Option H + H1 + With these options, maximum total pipe total pipe length is 30 feet...
- Page 35 installation Horizontal Venting with Three (3) 90 Elbows One 90 elbow = Two 45 elbows. Option V + V1 H + H1 With these options, maximum total pipe 2' Min. 1' Max. 3' Min. 4' Max. length is 30 feet with minimum of 12 feet 3' Min.
- Page 36 installation Vertical Venting with Three (3) 90 Elbows One 90 elbow = Two 45 elbows. Option H + H1 V + V1 With these options, max. total 1' Max. 1' Min. 3' Max. 3' Min. pipe length is 30 feet with min. 2' Max.
-
Page 37: Vertical Termination With Co-Linear Flex System In A Masonry Chimney
installation Vertical Termination with Co-Linear Flex System in a Masonry Chimney Masonry chimneys may take various contours which the flexible liner will accommodate. However, keep THE APPLIANCE MUST NOT BE the flexible liner as straight as possible, avoid unnecessary bending. CONNECTED TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL The Air Intake pipe must be attached to the inlet air collar of the termination cap. -
Page 38: Enting Arrangements - Vertical Terminations
installation Venting Arrangements - Vertical Terminations with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces Horizontal Distance (Feet) Horizontal Distance (Feet) The shaded area in the diagrams show the allowable vertical terminations. 38 | Regency P33E-11 Zero Clearance Direct Vent Gas Fireplace ®... -
Page 39: Unit Installation With Horizontal Termination
installation Unit Installation with Horizontal Termination Install the vent system according to the manufac- Below Grade Snorkel Installation turer's instructions included with the components. 5) Mark the wall for a 10" x 10" square hole. The If the Snorkel Termination must be installed below center of the square hole should line up with the 1) Set the unit in its desired location. -
Page 40: Unit Installation With Vertical Termination
installation 8) Slide the appliance and vent assembly towards 5) Cut a hole in the roof centered on the small the wall carefully inserting the vent pipe into the drilled hole placed in the roof in Step 2. The hole vent cap assembly. - Page 41 installation Vertical Termination - 4'' x 6-7/8'' Venting - Vertical Flex Vent Kit (946-755) VERTICAL TERMINATION 4" X 6-7/8" VENTING - VERTICAL FLEX VENT KIT (946-755) 1. Maintain the 1-½” (38 mm) clearance (air space) to combustibles when 11. Secure inner flex pipe to pipe adaptor by using Mill-Pac over the adaptor. passing through ceilings, walls, floors, enclosures, attic rafters or other Slide the inner pipe over adaptor and secure with 3 screws.
-
Page 42: Vertical Flue Extension Kit (Part #946-756)
installation Vertical Flue Extension Kit (part #946-756) VERTICAL FLUE EXTENSION KIT (PART # 946-756) 20 foot (6.1 m) Flex pipe Extension (Used in conjunction with the 946-755 Vertical Flex kit and 948-367/P flex CEILING FIRESTOP/FIRESTOP SPACER 4" (102 mm) inner to flex adaptor). -
Page 43: Pilot Adjustment
installation Pilot Adjustment Gas Pipe Pressure P33E-NG11 System Data Testing Periodically check the pilot flames. Correct With Flush Glass: flame pattern has two strong blue flames: The appliance must be isolated from the gas supply For 0 to 4500 feet altitude 1 flowing around the flame sensor and 1 piping system by closing its individual manual shut- Burner Inlet Orifice Sizes: #44... -
Page 44: Conversion From Ng To Lp
installation P33E Conversion from NG to LP Conversion from NG to LPG For P33E-11 Using SIT 885 NOVA Gas Valve for P33CE using SIT 886 NOVA Gas Valve THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION!! Remove burner orifice with a 1/2" Each Kit contains one LPG wrench and discard. Use another wrench Conversion Kit Part #438-977 to hold on to the elbow behind... -
Page 45: Optional Enamel Panels
P36D / P36DE/ P36E installation Optional Enamel Panels OPTIONAL ENAMEL PANELS Before installation, panels must be handled and cleaned as per instructions noted below: Black Enamel Panels • Black Enamel panels must be inspected for scratches and dimples prior to installation. All claims to be recorded at this time. Claims for dam- age after installation will not receive consideration. -
Page 46: Optional Brick Panels
installation Optional Brick Oak Log Set Installation Panels D) 251 A) 250 1) Undo the bottom 2 door latches and open and Read the instructions below carefully remove glass door. Remove logs. and refer to the diagrams. If logs are broken do not use the unit until they are 2) Attach the 2 rear brick retaining clips to the replaced. -
Page 47: Standard Flush Door
installation 8) Pull off ember size pieces of rock wool and gently place them on the front of the burner tray in the places shown in the photo below. Do not compress the rock wool, leave it loose. Separate platinum embers and place them on the front of the burner on and around the rock wool. -
Page 48: Optional Birch Log Set Installation
installation Optional Birch Log Set Installation BIRCH LOG INSTALLATION Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. Broken logs can interfere with pilot operation. Improper positioning of the logs may create carbon build-up and can alter the unit's performance which is not covered under warranty. - Page 49 installation 8. Install Log D - the wider end will rest on the left edge of the burner 11. Final install. tray and the narrower end will rest on Log C Final install Log D position 9. Install Log E - rest one end on Log C and the opposite end on the far 12.
-
Page 50: Vignette Faceplate And Safety Screen Installation
installation P33/P33E Vignette Faceplate and Safety Screen Installation VIGNETTE FACEPLATE AND SAFETY SCREEN INSTALL Install safety screen assembly by inserting tabs on assembly Hook tabs of Vignette frame onto unit in locations shown into slots on installed Vignette frame (see below). Screen below. -
Page 51: Optional Vignette Finishing Trim Install
installation Optional Vignette Finishing Trim Install VIGNETTE FINISHING TRIM *If fi nishing the unit Flush with Vignette Finishing Trim - remove top nailing strip from unit if installed–use nailing strip supplied with top trim piece. Side nailing strips are bent around side trim piece in fl ush fi nish application. NOTE: Remove the safety screen, Vignette Faceplate (P33 units Install the lower fi... -
Page 52: Optional Vignette Inlay Installation
installation OPTIONAL VIGNETTE INLAY Optional Vignette Inlay Installation NOTE: Inlay not exactly as shown below. 1. Remove Inner Vignette Frame from unit if already installed. 5. Secure the Inlay in position with supplied brackets, washers, and nuts as shown. 2. Line up the inlay top bracket in the space between the safety screen frame and Vignette Frame. -
Page 53: Optional Finishing Trim
installation Optional Finishing Trim OPTIONAL FINISHING TRIM NOTE: Remove the safety screen, Vignette Faceplate (P33 units only: remove 2 screws securing lower legs of Faceplate) and glass door prior to installing the Finishing Trim. Install the Finishing Trim sides as shown in the diagram, line up the holes in the side trim with the holes in the firebox side. -
Page 54: Safety Screen Installation
installation Safety Screen Installation Must be used with optional louvers SAFETY SCREEN INSTALLATION - MUST BE USED WITH OPTIONAL LOUVERS 1. Hook the safety screen frame over the glass door frame. 2. Gently lower screen on to glass door frame–two (2) magnets located on inside lower part of the screen frame will secure the screen to the glass door frame. 3. To remove–reverse steps. Magnet locations Optional Flush Louvers Installation 3. Install top louver by hooking louver on to brackets installed in Step 1. 07.21.15 919-558a Used with safety screen # 439-929... -
Page 55: Wiring Diagram
installation Wiring Diagram This heater does not require a 120V A.C. supply for operation but it is highly recommended to install the supplied AC adaptor to eliminate the need for batteries. In case of a power failure, the burner switch and the optional remote control will continue to operate if batteries are installed in the receiver. However, a 120V A.C. -
Page 56: Optional Wall Thermostat Installation
installation Optional Wall Thermostat Installation A wall thermostat may be installed if desired. Recommended: The Wall Thermostat should be mounted beside the Remote/Unit Receiver which comes standard with the appliance. 1) Run wires from thermostat into the unit. 2) Remove the green wire marked (TH) at the white connector-shown below. The noted wires will be located near the gas valve. Green Wires CAUTION Do not wire... -
Page 57: Optional Fan Installation
installation Optional Fan Installation OPTIONAL FAN INSTALLATION 120 Volt AC power is needed for the fan. The fan can be hard wired if desired. The outlet should be installed in the recep- tacle box on the left hand side by a qualified electrician. The neutral (wider) slot of the polarized outlet should be at the top. -
Page 58: Ac Power Adaptor Installation (For Surefire Systems)
installation AC Power Adaptor Installation (for Surefire Systems) AC POWER ADAPTOR INSTALLATION (FOR SUREFIRE SYSTEMS) An AC power adaptor is supplied with this appliance and may be installed as a constant power source for the SureFire system. NOTE: AC power adaptor is not required when using GTMF Remote with fan control module and must be disconnected. IMPORTANT: Recommend removing the 4-AA batteries in the SureFire receiver. -
Page 59: Wiring Diagram With Optional Fan
installation Wiring Diagram with Optional Fan CAUTION: Label all wires prior to disconnection Caution: Ensure that the wires do not touch any when servicing controls. Wiring errors can hot surfaces and are away from sharp edges. cause improper and dangerous operation. Regency P33E-11 Zero Clearance Direct Vent Gas Fireplace ®... -
Page 60: Lighting Procedure
operating instructions Lighting Procedure IMPORTANT: The remote control system supplied with this appliance has several options for starting/operating the appliance using the power button 3. After approximately 4 seconds the spark ignition system will spark for 60 and ON/OFF key on the hand held transmitter. seconds to light the pilot. -
Page 61: Copy Of The Lighting Plate Instructions
operating instructions Copy of the Lighting Plate Instructions FOR YOUR SAFETY READ BEFORE LIGHTING POUR VOTRE SÉCURITÉ – À LIRE AVANT LA MISE EN MARCHE WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. -
Page 62: Operating Instructions
operating instructions Operating Aeration Instructions Adjustment 1) Read and understand these instructions The air shutter can be adjusted by moving before operating this appliance. the adjusting wire up or down. The wire is accessed through the bottom opening(remove 2) Check to see that all wiring is correct and safety screen). -
Page 63: Maintenance Instructions
maintenance Normal Operating Sounds of Maintenance Instructions General Vent Gas Appliances Maintenance 1) Always turn off the gas valve before cleaning. For relighting, refer to lighting instructions. Keep Conduct an inspection of the venting system It is possible that you will hear some sounds the burner and control compartment clean by semi-annually. -
Page 64: Door Glass
maintenance Flush Glass Replacement Door Glass 1) with Vignette Faceplate installed: Remove the Vignette safety screen and Your Regency fireplace is supplied with high ® frame. See Vignette instructions in this temperature, 5 mm Neoceram ceramic glass that manual. will withstand the highest heat that your unit will produce. -
Page 65: Removing Valve
maintenance Removing Valve 9) Remove the 10 screws securing the valve tray assembly in place (diagram 2) and then lift the entire assembly out (diagram 3). 1) Shut off the gas and electrical supply. Screws Rear Log Stand 2) Remove the safety screen. 3) Open and remove the glass door. -
Page 66: Gas Appliance Maintenance
parts list Gas Maintenance Gas Appliance Maintenance Recommended Annual Routine Maintenance for Gas Fireplaces, Stoves and Inserts In order for your Regency appliance to continue to provide comfort to your home periodic maintenance must be performed to ensure it is operating at peak efficiency. The items in the list should be checked by a licensed gas service technician during the annual service check. Your unit may require more frequent maintenance checks if you notice any changes in how it operates. Operational changes to look for can include, but are not limited to, extended start up time, increased fan noise, residue/carbon build up, white build up on the glass/firebox, increased operating noise etc. Should any of these or other conditions arise, discontinue use and schedule a service check with your local licensed gas technician. The list below shows items your licensed service technician will need to check and service at least annually. Clean Inspect Check • Glass • Pilot assembly • Voltage on thermocouple/thermopile (mil- • Interior bricks / panels • Burner livolt models) • Burner ports & burner air shutter • Pressure relief gaskets/doors •... -
Page 67: Main Assembly
parts list Main Assembly Part # Description Part # Description 948-247 Door Handle 430-057 Brick Clip - Bottom Thermodisc Bracket 438-917 Fan Kit Complete 910-428 Duplex Receptacle 910-429 Box - Receptacle 910-331/P Replacement Fan Motor (120 Volts) 910-430 Cover - Receptacle 911-159 Power Cord (120 Volts) 904-687... - Page 68 parts list HEAT WAVE DUCT KIT #946-556 BRICK PANEL SET FAN ASSEMBLY 68 | Regency P33E-11 Zero Clearance Direct Vent Gas Fireplace ®...
-
Page 69: Burner & Log Assembly
parts list Burner & Log Assembly Part Description 430-055 Gasket - Valve Access Plate - NG/LP 911-084 Valve SIT - NG 911-085 Valve SIT - LP 911-276 Pilot Assy - NG 911-277 Pilot Assy - LP 904-568 Orifice #44 - Natural Gas 904-575 Orifice #55 - Propane 936-170... -
Page 70: Vignette Faceplate And Finishing Trim
parts list Vignette Faceplate and Finishing Trim Part # Description Part # Description 439-922 Vignette Faceplate Platinum 439-928 Vignette Finishing Trim 439-923 Vignette Faceplate Black Chrome 439-948 Vignette Door Inlay Black Chrome 439-924 Vignette Faceplate Black 439-949 Vignette Door Inlay Mt. Black 439-926 Vignette Faceplate Tuscan Sunset 439-950... -
Page 71: Safety Screen And Louvers
parts list Safety Screen and Louvers Part # Description 439-920 Flush louvers black (Set) 439-929 Safety Screen 948-223 Regency Logo Plate ® 430-940 3-sided Finishing Trim Regency P33E-11 Zero Clearance Direct Vent Gas Fireplace ®... -
Page 72: Warranty
warranty Limited Lifetime Warranty FPI Fireplace Products International Ltd. (for Canadian customers) and Fireplace Products U.S., Inc. (for U.S. customers) (collectively referred to herein as “FPI”) extends this Limited Lifetime Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. The items covered by this limited warranty and the period of such coverage is set forth in the table below. - Page 73 warranty At all times FPI reserves the right to inspect reported complaints on location in the field claimed to be defective prior to processing or authorizing of any claim. Failure to allow this upon request will void the warranty. All warranty claims must be submitted by the dealer servicing the claim, including a copy of the Bill of Sale (proof of purchase by you).
- Page 74 warranty Limitations of Liability: The original purchaser’s exclusive remedy under this warranty, and FPI’s sole obligation under this warranty, express or implied, in contract or in tort, shall be limited to replacement, repair, or refund, as outlined above. IN NO EVENT WILL FPI BE LIABLE UNDER THIS WARRANTY FOR ANY INCIDENTAL OR CONSEQUENTIAL COMMERCIAL DAMAGES OR DAMAGES TO PROPERTY.
- Page 75 warranty Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.
- Page 77 notes Regency P33E-11 Zero Clearance Direct Vent Gas Fireplace ®...
- Page 78 notes 78 | Regency P33E-11 Zero Clearance Direct Vent Gas Fireplace ®...
- Page 80 Installer: Please complete the following information Dealer Name & Address: _______________________________________ ___________________________________________________________ Installer: ___________________________________________________ Phone #: ___________________________________________________ Date Installed: _______________________________________________ Serial #: ____________________________________________________ Printed in Canada Regency, Panorama, AstroCap and Surefire are trademarks of FPI Fireplace Products International Ltd. © Copyright 2023, FPI Fireplace Products International Ltd. All rights reserved.
Need help?
Do you have a question about the Panorama P33E and is the answer not in the manual?
Questions and answers