Table of Contents
Advertisement
Switch Passage Function (On/ Off)
This operation allows Passage Function to be toggled On and Off.
Step
Detailed Instructions
1.
Power lock.
Power the lock by depressing the outside lever.
2.
Enter Master User
Enter the Master User or Manager User combina-
or Manager User
tion. The lock will beep/flash the green LED on
combination
each keystroke entered. If the Clear key is pressed
during data entry, the lock responds with one beep/
flash of the green LED followed by the red LED, and
all digits of the combination must be re-entered. The
lock responds with three beeps/flashes of the green
LED to indicate available entry. If the combination is
not valid, the lock responds with three beeps/flashes
of the red LED.
3.
Press
then 13.
Before re-lock time expires, press
followed by the 1 key and then the 3 key. The lock
responds with two beeps/flashes of the green LED.
Delete Access User(s)
Note: If at any time during the procedure the lock power drops below a sufficient
level for operation, the lock will continually beep and flash the red LED, prompt-
ing the user to depress the outside lever to provide additional power.
Step
Detailed Instructions
1.
Power lock.
Power the lock by depressing the outside lever.
2.
Enter Master User
Enter the Master User or Manager User combina-
or Manager User
tion. The lock will beep/flash the green LED on
combination
each keystroke entered. If the Clear key is pressed
during data entry, the lock responds with one beep/
flash of the green LED followed by the red LED, and
all digits of the combination must be re-entered. The
lock responds with three beeps/flashes of the green
LED to indicate available entry. If the combination is
not valid, the lock responds with three beeps/flashes
of the red LED.
3.
Press
then 3.
Before re-lock time expires, press
followed by the 3 key. The lock responds with two
beeps/flashes of the green LED.
26
Step
4.
Enter Access User
ID.
5.
Enter Access User
ID again.
6.
Repeat Steps 4
and 5 to delete
more users or go
Step 7.
(Enter key)
Caution: If you are deleting multiple Access Users, you may need to depress
the outside lever to provide additional power.
7.
Press
Deactivate Manager User
Step
1.
Power lock.
2.
Enter Master User
combination.
3.
Press
(Enter key)
Detailed Instructions
Enter an Access User's ID to be deleted (or press
the Enter key to exit.) The lock responds with two
beeps/flashes of the green LED.
Confirm the Access User's ID by re-entering it. The
lock responds with two beeps/flashes of the red
LED if the combination was unconfirmed or the User
ID was not found in the Access User table. Other-
wise, the lock responds with four beeps/flashes of
the green LED.
The Access User is now deleted from the lock.
If additional Access Users are to be deleted, repeat
Steps 4 and 5 until all Access Users have been
deleted. If additional Access Users are not to be
deleted, go to Step 7.
.
Press
(Enter key) to exit this procedure. The
lock responds with two simultaneous beeps/flashes
of the green and red LEDs and exits this procedure.
Detailed Instructions
Power the lock by depressing the outside lever.
Enter the Master User combination. The lock will
beep/flash the green LED on each keystroke
entered. If the Clear key is pressed during data
entry, the lock responds with one beep/flash of
the green LED followed by the red LED, and all
digits of the combination must be re-entered. The
lock responds with three beeps/flashes of the green
LED to indicate available entry. If the combination is
not valid, the lock responds with three beeps/flashes
of the red LED.
then 91.
Before re-lock time expires, press
followed by the 9 key and then the 1 key. The lock
responds with two simultaneous beeps/flashes of
the green and red LEDs.
The Manager User is now deactivated.
(Enter key)
27
Advertisement
Table of Contents
