Xerox WorkCentre M20 Service Manual page 313
Hide thumbs
Also See for WorkCentre M20:
- Service manual (202 pages) ,
- Installation instructions (2 pages) ,
- System administration manual (218 pages)
Table of Contents
Advertisement
8.
Install the PBA foreign device interface harness. Connect the harness to CN38 (M20F),
CN17 (4118) or CN20 (2218), Figure 3.
NOTE: The M20F PBA main connector (CN38) is shown in Figure 3. The 4118 and 2218
PBA main has a horizontal connector.
Figure 3 Harness install
9.
Reinstall the MEA unit rear cover.
10. Connect the foreign device interface harness to the D type connector on the PBA foreign
device interface.
11. Go to Enabling the Foreign Device Interface.
Enabling the Foreign Device Interface
1.
Switch on the machine.
2.
Press the 'Machine Status' key.
3.
Use the up/down keys to scroll through the options. Select 'System Admin Tools'.
4.
Press the 'Enter' key.
5.
If the 'System Admin Tools' are password protected, enter the password or ask the sys-
tem administrator to enter the password.
6.
Use the left/right keys to scroll through the options. Select 'Auxiliary Access'.
7.
Press the 'Enter' key.
8.
Select 'On' in the Auxiliary Access sub-menu.
9.
Press the 'Enter' key.
10. Press the 'Menu/Exit' key twice to return to 'Ready to Copy' mode.
11. If the 'System Admin Tools' were not password protected, perform the relevant Enabling
Password Protect procedure.
WorkCentre M20, 4118, FaxCentre 2218 Family
NOTE: The 'System Admin Tools' must be password protected to prevent users making
free copies.
12. Go to Enabling Password Protect (M20F) or Enabling Password Protect (4118 and 2218).
Enabling Password Protect (M20F)
NOTE: Ensure that the system administrator is present during this procedure.
1.
Press the 'Machine Status' key.
2.
Use the up/down keys to scroll through the options. Select 'System Admin Tools'.
3.
Press the 'Enter' key.
4.
Use the left/right keys to scroll through the options. Select 'Password Protect'.
5.
Select 'Yes'.
6.
Press the 'Enter' key.
CN2
7.
Enter a password, or get the system administrator to enter a password.
NOTE: Ensure that the system administrator records the password for future reference.
8.
Press the 'Enter' key.
9.
Press the 'Menu/Exit' key twice to return to 'Ready to Copy' mode.
Enabling Password Protect (4118 and 2218)
CN38 (M20F)
CN17 (4118)
NOTE: Ensure that the system administrator is present during this procedure.
CN20 (2218)
1.
Press the 'Machine Status' key.
2.
Use the up/down keys to scroll through the options. Select 'System Admin Tools'.
3.
Press the 'Enter' key.
4.
Use the left/right keys to scroll through the options. Select 'Password Protect'.
5.
Press the 'Enter' key.
6.
Use the left/right keys to scroll through the options. Select 'System Admin Tools'.
7.
Press the 'Enter' key.
8.
Use the left/right keys to scroll through the options. Select 'Protect All'.
9.
Press the 'Enter' key.
10. At the 'Protect More?' prompt, use the left/right keys to select 'No'.
11. Press the 'Enter' key.
12. Enter a password, or get the system administrator to enter a password.
NOTE: Ensure that the system administrator records the password for future reference.
13. Press the 'Enter' key.
14. Confirm the password.
15. Press the 'Enter' key.
16. Press the 'Menu/Exit' key three times to return to 'Ready to Copy' mode.
December 2006
8-5
Accessories
ACC 2
Advertisement
Chapters
Table of Contents
