Page 2
Information in this manual is copyrighted to the respective owners. All rights are reserved by Jakob Hatteland Display AS. This information may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form without the prior written consent of Jakob Hatteland Display AS.
Contents Contents .................. Contents of package ................6 General ..................7 Introduction to Jakob Hatteland Display AS ........8 About this manual ................9 Basic Construction - Maritime Multi Display ........10 Touchscreen products ..............11 Location of Touchscreen label ............12 Product Labels (Example) ..............
Page 4
Specifications - JH 20T06 MMD (DVI) ..........41 Specifications - JH 23T02 MMD (DVI) ..........42 Technical Drawings .............. Technical Drawings - JH 10T06 MMD (DVI) ........44 Standard Version ................44 Bracket(s) Version ................45 Technical Drawings - JH 15T05 MMD (DVI) ........46 Standard Version ................46...
Page 5
Contents Technical Drawings - Accessories ........59 10 Inch Sun Visor ................60 17” >> 23” Rotary Bracket ..............61 17 Inch > 20 Inch Bracket ..............62 15” TFT to 19” RACK adapter ............63 19” TFT to 21” CRT adapter ............. 64 19 Inch Sun Visor ................65 VESA Bracket ...................66 Water Cover ..................67...
Contents of package This product is shipped with: Item Description Illustration 4 pcs of PAN M6X25 black bolts with M6 plastic washer. These should only be used to secure the display into a console. Note: If you prefer your own bolts, make sure they are minimum M6 and 25mm in length for security reasons.
Jakob Hatteland Display AS Introduction to Jakob Hatteland Display AS Founded in 1987, Jakob Hatteland Display (JHD) offers the widest range of type approved marine monitors, panel computers and type approved marine computers for the worldwide commercial, naval, yacht and cruise market.
The combination of the reliable design of the marine TFT-LCD modules, together with industrial computer boards, allows Hatteland Display to offer a product range for customer applications where space is critical and full function is desired in a single unit. In particular, the standardized ETX-board form factor allows full flexibility when it comes to processor choice.
Touchscreen products Introduction to Jakob Hatteland Display products with touchscreen We use both Resistive and Capacitive touchscreen solutions for our products. Please visit our website to verify what product and touchscreen solution your product have. Capacitive Touchscreen Capacitive touchscreens operate using oscillator circuits that are located in each corner of the glass overlay and measure the capacitance of the area to be “touched”.
Up-2-date touchscreen drivers and documentation: Please visit the 3rd party website as indicated on the label. You can also visit our website www.hatteland.com to view the full list of our models with touchscreen. Before using the touchscreen, it should be calibrated for your system.
: ELO TouchSystems Touch Controller : 2210 Serial Controller P/N 055165-000 Driver Download : www.elotouch.com VSD100564-2210 Product Information Manufacture: Product: Product type: Jakob Hatteland Display 19 Inch JH 19T01MMD-A1-81 NORWAY Serial Number 100W 115VAC/50-60Hz 20VAC/50-60Hz Manufacturer & Country Product & Serial Number...
General Installation Recommendations Installation and mounting 1. Most of our products are intended for various methods of installation or mounting (panel mounting, bracket mounting, ceiling/wall mounting etc.); for details, please see the relevant mechanical drawings. 2. Adequate ventilation is a necessary prerequisite for the life of the product. The air inlet and outlet openings must definitely be kept clear;...
General Installation Recommendations Ergonomics 1. Adjust the unit height so that the top of the screen is at or below eye level. Your eyes should look slightly downwards when viewing the middle of the screen. 2. Adjust screen inclination to remain gaze angle to the centre of the screen approximately perpendicular to the line of gaze.
Use only high quality shielded signal cables. For RGB/DVI cables use only cables with separate coax for Red, Green and Blue. Jakob Hatteland Display can supply a varity of high quality RGB/ DVI, RS232, PARALLEL, LAN and USB cables intended for this use.
General Installation Recommendations Maximum Cable Length The RGB/DVI cable should generally be kept as short as possible to provide a high quality output on the display. The maximum cable length will depend on the signal resolution and frequency, but also on the quality of the signal output from the computer. We recommend using 60Hz vertical frequency for our displays.
User Controls POWER SWITCH: This TFT display features a Instant-ON/Delay-OFF switch, which ensures that the display is not turned off by user accident. Assignable Hot keys Auto Power LED Dimmer Power ON: To turn the display on, press down Indication Mark the power switch.
Page 23
Operation MENU UP / DOWN Buttons Adjust Buttons -/+ USER CONTROLS: The On Screen Display (OSD menu) controls are located under the metal hatch on the left side of the display. To begin understanding the menu and its usage, just follow these steps for a quick start. 1: Press the “MENU”...
OSD Menu Overview Mode 1 - Function layout in RGB / DVI MODE Simplified/Normal OSD Menu: (User menu) Note that to be in RGB / DVI MODE, a computer signal must be present in full screen, i.e Windows or other operating system/radar system. Having a PIP view simultaneously will not interfere or change the menu structure in any way.
Page 25
OSD Menu Overview Mode - Function layout in VIDEO MODE Simplified/Normal OSD Menu: (User menu) Note that to be in VIDEO MODE, a video signal must be present in full screen, i.e from a camera, VCR or DVD player. Video Adjustment Color Tint...
OSD Menu Functions BRIGHTNESS AND CONTRAST: (No function in DVI mode) Selecting this function will enable the user to adjust brightness and contrast for the display. (No Function in DVI) BRIGHTNESS: Increase/decrease brightness level, total: 100 steps (No Function in DVI) CONTRAST: Increase/decrease contrast level, total: 100 steps COLOR TEMPERATURE Selecting this function will enable the user to modify the warmness of the picture.
Page 27
OSD Menu Functions STATUS: Selecting this function will display graphic information such as resolution and frequency. POSITION: (No function in DVI mode) Selecting this function will enable the user to position the image within the display area. (No Function in DVI) IMAGE UP/DOWN : Position the image vertically using “UP”...
Page 28
OSD Menu Functions GRAPHIC SCALING MODES: Selecting this function will enable the user to configure the graphic scaling of the RGB/DVI or VIDEO image. The change will happen realtime. Note: Some of these functions will impact on image quality, and will therefore not show the optimal 1:1 picture with correct aspect ratio and resolution suitable for the TFT module.
Page 29
OSD Menu Functions UTILITIES: Selecting this function will enable the user to configure the OSD menu, define hot keys, verify BIOS Firmware version and miscellaneous operations. USER SETTING: (Press “+” to access the sub-menu) DPMS : Disable / Enable the DPMS function. DISPLAY INPUT : Disable / Enable input source name upon power up.
Page 30
OSD Menu Functions CALIBRATE RGB GAIN : Color Calibration. Press “+” to automatically adjust it. DISPLAY ORIENTATION: (Press “+” to access the sub-menu) Will flip/inverse the display area including PIP view. Press “+” to choose between: Normal / Horizontal Inverse / Vertical Inverse / Inverse LOAD (FACTORY) DEFAULTS: (Press “+”...
Physical Connections - MMD/STD Models Connection area of display (illustration) RGB Out or Touch (Optional) Power Input Serial Interface(opt) RGB IN Composite In S-Video In DVI-D IN (newer models) NOTE: Available connectors/locations may vary depending on model ! TOUCHSCREEN / VGA OUT: (optional) Connect the RS-232 cable to the D-SUB 9P Connector (female) on the rear side of the TFT display.
Page 32
Appendix chapter “Serial Communication (SCOM) Interface” in this manual. For in-depth information, see www.hatteland.com - “Support/Accessories/JHSCOM/Technical Manual”. Note: If you have optional accessories beyond these standard connectors described here, please visit our website at www.hatteland.com for separate documentation/specifications regarding accessories (when made available). INB100005-1 (Rev 19) IND100133-1...
APPENDIX II – SUPPORTED MODES TABLE Preset Signal Timings Graphic/Video Modes Supported Mode Resolution Clk [MHz] Horizontal freq Vertical freq Sync Mode [KHz] [Hz] E1_70 640x350 25.175 31.469 Digital Separate Sync E1_70 640x350 25.175 31.469 Sync On Green (with or without serrate pulse) E1_70 640x350 25.175...
Page 34
Preset Signal Timings X_60 1024x768 65.000 48.363 Sync On Green (with or without serrate pulse) X_60 1024x768 65.000 48.363 Composite Sync (with or without serrate pulse) X_70 1024x768 75.000 56.476 Digital Separate Sync X_70 1024x768 75.000 56.476 Sync On Green (with or without serrate pulse) X_70 1024x768 75.000...
: S-Video (SVHS) plug • Contrast Ratio : 300:1 (typical) • AC Power signal : Std IEC Inlet Model JH 10T06 MMD A1 • Light Intensity : 350 cd/m2 (typical) • DC Power signal : Screw terminal Model JH 10T06 MMD A2 •...
Specifications - JH 15T05 MMD (DVI) Note: All specifications are subject to change without prior notice! T E C H N I C A L D E S C R I P T I O N M E C H A N I C A L D E S C R I P T I O N TFT Technology: Physical Dimensions: •...
Specifications - JH 17T02 MMD (DVI) Note: All specifications are subject to change without prior notice! T E C H N I C A L D E S C R I P T I O N M E C H A N I C A L D E S C R I P T I O N TFT Technology: Physical Dimensions: •...
Specifications - JH 19T02 MMD (DVI) Note: All specifications are subject to change without prior notice! T E C H N I C A L D E S C R I P T I O N M E C H A N I C A L D E S C R I P T I O N TFT Technology: Physical Dimensions: •...
Specifications - JH 20T03 MMD (DVI) Note: All specifications are subject to change without prior notice! T E C H N I C A L D E S C R I P T I O N M E C H A N I C A L D E S C R I P T I O N TFT Technology: Physical Dimensions: •...
Specifications - JH 20T06 MMD (DVI) Note: All specifications are subject to change without prior notice! T E C H N I C A L D E S C R I P T I O N M E C H A N I C A L D E S C R I P T I O N TFT Technology: Physical Dimensions: •...
Specifications - JH 23T02 MMD (DVI) Note: All specifications are subject to change without prior notice! T E C H N I C A L D E S C R I P T I O N M E C H A N I C A L D E S C R I P T I O N TFT Technology: Physical Dimensions: •...
Pin Assignments - Common Connectors Note: Not all connectors may be available on your specific product. This depends on the amount of additional hardware installed from factory, or customized solutions. These pin assignments are for the common connectors used. Connectors are seen from users Point Of View (POV). Pin Assignments - USB TYPE A Pin Assignments - RJ5 10/100 LAN Pin 4: Ground...
Page 71
Pin Assignments - Common Connectors Pin Assignments - 25P Parallel 1 12 11 10 9 8 7 6 5 2 1 25 2 2 22 21 20 19 18 17 16 15 1 Pin 01 - STROBE This signal indicates to the printer that data at PD7..0 are valid. Pin 02 - DATA0 Parallel data bus from PC board to printer.
Serial Communication (SCOM) Interface Installation in display Connectorization The remote control has two 9 pin D-subs for communication. For systems with more than one display, the displays are connected together through the unoccupied D-sub. It is regardless which one is used, with exception for the case described in 2.2.1.2, where COM-1 is connected to another display, and COM-2 is connected to the pc.
Serial Communication (SCOM) Interface Communication settings #1 (before Jan 2005) The communication options are set by switches, placed at the backside of the display. For most displays, these switches are labelled like seen on the illustration below. For adjustments, a thin object is required for reaching the switches.
Serial Communication (SCOM) Interface Communication settings #2 (after Jan 2005) The communication options are set by switches, placed at the backside of the display. These switches are protected behind a hatch mounted with four screws. Unscrew those, and remove the hatch.
Basic Trouble-shooting COMMON ERRORS: (This is a generic description of possible issues for a varity of products) If for some reason there should be something wrong with the picture quality or no picture present, check the symptoms carefully and try to cure it with the hints below: NO PICTURE / LED BEHAVIOUR: If there is no light at all in the LED at the FRONT, check power cables.
Declaration of Conformity We, manufacturer Jakob Hatteland Display A/S Åmsosen, N-5578 Nedre Vats, Norway declare under our sole responsibility that the MMD, MMC, STD and MIL products is in conformity with the following standards in accordance with the EMC Directive...
Return Of Goods Information Return of goods: (Applies not to warrenty/normal service/repair of products) Before returning goods, please contact your system supplier before sending anything directly to JHD. When you return products after loan, test, evaulation or products subject for credit, you must ensure that all accessories received from our warehouse is returned to JHD.
Jakob Hatteland Display AS charge NOK 50,- in forwarding fee for orders below NOK 1000,-. For orders below NOK 1000,- Jakob Hatteland Supply AS charge freight according to expenses, and NOK 25,- for packing. For handling requested beyond ordinary hours NOK 250,- is charged. Express service is charged with NOK 100,- + freight charges.
Page 79
Terms 11) RESPONSIBLITY Seller undertake to deliver faultless and functional capable goods according to existing technical specifications. Seller disclaim responsibility for any damage or loss which directly or indirectly may be caused due to failure or defect with the delivered goods, if carelessness from the seller can be limited up to the cost of the goods. The supplier’s responsibility for defects with the supplied goods do not include secondary damage or loss.
Page 80
Terms INSTRUCTIONS FOR THE CONSIGNEE 1) CONTROL Control the goods immediately by receipt. Examine the quantity towards the invoice/packinglist/shipping documents. Look for outward defects on the packing which may indicate damage on or loss of contents. Control the container and the seals for any defects.
For certain versions the entire graphical board must be changed by a qualified Hatteland technician or a representative. A BIOS software upgrade is not possible.