Page 1
21” CRT JH 21C07 MDK 21 inch Marine Desktop Color Monitor Jakob Hatteland Display AS Created : 13 Jul, 2001 Modified : 13 Nov, 2001 Created by: Stein Eikesdal Title : IND100050-1 Subject : JH21C07MDK-UserManual Description: Internet release for customers.
The monitor is tested according to the maritime standard IEC945-3. This is a technically lighter desktop monitor of the Hatteland monitor type JH 21C06 version. JH 21C07 MDK - 21 inch Marine Desktop Color Monitor CONTENTS: OPERATION......................
OPERATION Product: JH 21C07MDK Power Light Indicator Power Switch Degauss Button POWER SWITCH: Power ON: To turn the monitor on, press the power switch. The power light indicator (Power LED) will turn green. Note: If no VGA signal sync is present, it will turn orange after 10 seconds and the message “NO SYNC.
USER CONTROLS PANEL Product: JH 21C07MDK Select Function Buttons Adjust Buttons Input Select USER CONTROLS: The On Screen Manager (OSD EasyMenu) controls are located on the left side of the monitor. To begin adjusting any of the monitor’s functions, press then desired function item, and then refer to the table below to make any changes to the picture.
OSD MENU USAGE Product: JH 21C07MDK AVAILABLE FUNCTIONS: Each of the “function buttons” have two sets of parameters that can be modified. One upper parameter and one lower parameter. To modify any of the parameters use either of the “adjust buttons” sets. The EasyMenu display will also indicate what parameter is beeing modfied.
USAGE / STORE Product: JH 21C07MDK AVAILABLE FUNCTIONS: (continued) PARAMETER FUNCTION BUTTON ADJUST BUTTON RESULT Stops or operates the horizontal moire changing circuit. H. Moire Reduction Increases or decreases the strength of the horizontal moire changing circuit. Stops or operates the vertical moire changing circuit. V.
PHYSICAL CONNECTIONS Product: JH 21C07MDK Rear side of monitor Signal Inputs: Power Terminal Input 1 Input 2 SIGNAL INPUTS: There are two signal inputs connectors allowing you to display two signals from separate sources. Connect the VGA cable to the desired D-SUB 15P Connector (female) on the rear side of the monitor. If possible, screw the VGA cable to the D-SUB connector and make sure you don’t bend any of the pins inside the connector.
PIN ASSIGNMENTS Product: JH 21C07MDK VGA D-SUB 15P CONNECTORS FEMALE: 15 14 13 Pin Number: Description (Input 1): Description (Input 2): red video red video green video (sync. optional) green video (sync. optional) blue video blue video no pin no pin no connection no connection red ground...
SIGNAL CHECKING Product: JH 21C07MDK SIGNAL CHECK: To refer to the input signal condition, press any of the adjust buttons. The horizontal and vertical frequency will be indicated in the lower part of the picture. Above: Sample of “Input Select” EasyMenu. AUTOMATIC SIGNAL CHECK: When the CRT monitor has detected the change of the signal input condition, it will indicate the condition automatically, as follows:...
SIGNAL CHECKING Product: JH 21C07MDK Indication 3: The Power Light Indicator flashes. Condition 3: This happens when the monitor will go into the power saving mode. (Refer to page 6) Solution 3: Verify power switch of the computer and check cable connection. Indication 4: The EasyMenu indicates the message “INVALID SCAN FREQ”.
PRESETS / POWER SAVING Product: JH 21C07MDK PRESET SIGNAL TIMING TABLE: Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. The following industrial standard settings have been pre-programmed by the factory. Preset Resolution Vert. Frequency(Hz) Horiz.
Adjustment controls 230 MHz Input Select Specification and design are subject to change without notice. For additional information, datasheets and Jakob Hatteland Display AS support for this product, please visit our Åmsosen, N-5578 Nedre Vats, Norway website: http://www.hatteland.com Phone : +47 5276 3700...