Specifications - Banner R-GAGE K50R Instruction Manual

®
R-GAGE K50R Radar Sensor

7 Specifications

Range
The sensor can detect an object at the following ranges, depending on
the material of the target: 100 mm to 2.5 m
Operating Principle
Pulsed coherent radar (PCR)
Operating Frequency
60.5 GHz
Supply Voltage (Vcc)
10 V DC to 30 V DC
Use only with a suitable Class 2 power supply (UL) or Limited Power
Supply (CE)
Power and Current Consumption, exclusive of load
Standard models:
Power consumption: <1.0 W at 24 V
Current consumption: <35 mA at 24 V
Pro models:
Power consumption: <1.5 W at 24 V
Current consumption: <55 mA at 24 V
Supply Protection Circuitry
Protected against reverse polarity and transient overvoltages
Linearity
< ± 2 mm from 100 mm to 250 mm
< ± 4 mm from 250 mm to 800 mm
< ± 8 mm from 800 mm to 2.5 m
Reference target with RCS = 1m²
Delay at Power-up
< 1 s
Output Configuration
Discrete Output 1 (Black Wire): Configurable PNP or NPN output
Discrete Output 2 (White Wire): Configurable PNP or NPN output or
Pulse Frequency Modulated (PFM) output
Output Ratings
Current rating = 50 mA maximum each
Black wire specifications per configuration
Output High
PNP
Output Low
Output High
NPN
Output Low
White wire specifications per configuration
Output High
PNP
Output Low
Output High
NPN
Output Low
3
Repeatability
4 mm from 100 to 250 mm
8 mm from 250 mm to 800 mm
16 mm from 800 mm to 2.5 m
Maximum Output Power
EIRP: 10dBm
Output Protection
Protected against output short-circuit
3 At medium response speed.
22
Remote Input
Allowable Input Voltage Range: 0 to Vsupply
Active High (internal weak pull-down): High state > (Vsupply - 2.25 V) at
2 mA maximum
Active Low (internal weak pull-up): Low state < 2.25 V at 2 mA maximum
Response Time
Discrete output response: 200 ms
Speeds given for fast mode.
Indicators
Standard models:
Pro models: User configurable
Construction
Housing: Polycarbonate
Window: Polycarbonate
Connections
Integral M12 quick disconnect
Models with a quick disconnect require a mating cordset
Vibration and Mechanical Shock
All models meet MIL-STD-202F, Method 201A (Vibration: 10 Hz to 60 Hz
maximum, 0.06 inch (1.52 mm) double amplitude, 10G acceleration)
requirements. Method 213B conditions H&I.Shock: 75G with device
operating; 100G for non-operation
Operating Temperature
Standard model: –40 °C to +60 °C (–40 °F to +140 °F)
Temperature Effect
<±5 mm from –40 °C to +60 °C (–40 °F to +140 °F)
≥ Vsupply - 2.5 V
Environmental Rating
IP67
≤ 1V (loads ≤ 1 MegΩ)
Certifications
≥ Vsupply - 2.5 V
≤ 2.5 V
≥ Vsupply - 2.5 V
≤ 2.5 V (loads ≤ 70 kΩ)
≥ Vsupply - 2.5 V
≤ 2.5 V
Contains FCC ID: 2AQ6KA1001
Contains IC: 24388-A111
for others, contact Banner Engineering
Advanced Capabilities
Country of Origin
USA
www.bannerengineering.com - Tel: + 1 888 373 6767
Power LED/Signal Strength: Green or blue depending on sensor
state
Output LEDs: Amber, target within taught discrete output status
Note: A shielded cable is required if the
sensor is mounted outdoors or if the cable is
longer than 30 m (98.4 ft).
Banner Engineering Europe
Park Lane, Culliganlaan 2F bus 3,
1831 Diegem, BELGIUM
Turck Banner LTD Blenheim
House, Blenheim Court, Wickford,
Essex SS11 8YT, Great Britain