Summary of Contents for Fichtelbahn ReadyServoTurn
Page 1
FichtelBahn TERM Power TAST DCC BiDiB 12V - 18V eady Line ReadyServoTurn 4-fach BiDiB-Servodecoder FichtelBahn with 4x Relais and 4x Input Made in Germany Servo 0 Servo 1 Servo 2 Servo 3 Data Data INPUT REL 0 REL 1 REL 2...
Page 2
Line FichtelBahn What is a ReadyServoTurn for? The ReadyServoTurn is an accessory decoder that is operated by the BiDiBus and pro- vides servo outputs, relay outputs and inputs for the model railway layout. Please notice: The ReadyServoTurn cannot be controlled by digital command stations that only send digital turnout commands to the accessory decoders (e.g.
02. Introduction ...................... 4 03. Technical Data....................4 04. Connecting the ReadyServoTurn ..............5 05. Configuration of the module ................11 06. Module settings for the ReadyServoTurn ............29 07. LED indication ....................31 09. Firmware update ....................33 10. Support case and further help ................34 11.
Designated Use The normal use of the ReadyServoTurn is for model making especially digital model railways according to this manual. Any improper use will leas to loss of warranty. Package Contents...
Line FichtelBahn 04. Connecting the ReadyServoTurn B1 B2 TERM Power TAST DCC BiDiB 12V - 18V eady Line ReadyServoTurn 4-fach BiDiB-Servodecoder FichtelBahn with 4x Relais and 4x Input Made in Germany Servo 0 Servo 1 Servo 2 Servo 3...
Page 6
REL 1 will lead to unrepairable damage to the module! 04.2 Connecting to the BiDiBus The ReadyServoTurn has two parallel BiDiBus sockets (B1/B2) which can be used to place the module at any desired position within the bus by using patch cables. .
Page 7
Background knowledge” on page 32.) A BiDiB-IF2 is shown as symbolic interface for any type (e.g. GBM Master / GBMboost Master).. In the following figure, the ReadyServoTurn was placed as the last module of the BiDiBus. In this case, the two terminating jumpers for the BiDiB and DCC termination must be fitted on the module.
Page 9
TAST the tolerance is unimportant. Here a large travel distance should be chosen and servos DCC BiDiB with metal gears should be used. In the FichtelBahn-Shop you will find a reliable and inexpensive solution with the article no. 410100 Line ReadyServoTurn 04.3.1 Servo protection mechanisms...
Page 10
Line FichtelBahn 04.4 Connecting a relay output The ReadyServoTurn has 4 relay outputs (changeover contact) that can be used as a isolated application or with the servo motors and inputs. The example illustration TERM Power TAST DCC BiDiB 12V - 18V shows a frog polarisa- tion on relay output 0.
The BiDiB-Wizard 2 is a Java program for displaying and configuring the BiDiB modules on the BiDiBus. The current version BiDiB-Wizard 2 is available for free download in our BiDiB-Wiki at https://wiki.fichtelbahn.de ( in the overview tree under „Programme für BiDiB“...
Page 12
By double clicking on a node in the node tree view (5.) this node will be loaded and its functions und options will be shown in the node detail window (6.). For the “ReadyServoTurn” module, there are two ways of achieving an operational state: 1.
Page 26
Depending on the control program, different protocols are supported - “Accessory” is required here. Port The ReadyServoTurn could be used to control 4 turnouts that can be addressed via the accessories 0-3, for example. This accessory is selected in the port selection menu.
Page 27
Line FichtelBahn 05.4 Servo motion profiles The ReadyServoTurn offers predefined curves for typical model railway motion sequences. These curves can be changed for every servo movement in the node con- figurator or in the servo settings (tab: Servo ports). Linear / Linear...
Line FichtelBahn 06. Module settings for the ReadyServoTurn All settings that can be adjusted for the ReadyServoTurn can be accessed via the configuration tool “BiDiB-Wizard 2”. It is not possible to change the settings at the unit itself. 06.1 ReadyServoTurn features Right-clicking on the ReadyServoTurn in the node list opens a window with further options.
Page 30
(e.g. node configuration) by BiDiB Wizard 2. Changes to the features or CV registers are not necessary and should not be made without consulting FichtelBahn technical support. 06.3.1 PowerOFF behaviour of the servos Servo x:...
07.2 Error states at module start up 10x fast flashes (1, 2, 3) Power-ON LED, BiDiB-Identify LED, Message LED No bootloader found / no firmware update possible (contact the FichtelBahn-Support) Continuous Flashing (1, 2, 3) Power-ON LED, BiDiB-Identify LED, Message LED EEPROM faulty (conduct a firmware update, see “09.
„ReadyServoTurn“ in the tree view. The ReadyServoTurn node will be loaded and displayed in the right window. (The illustration shows a different module name, but the function is identical). Click on the button “Update firmware” (2.). In the new window choose the firmware zip file (3.)
(A). In the tree view appears a module with the name “ReadyServoTurn Bootloader” (1.). This is a safety function to be able to redo the function update (see “09 Firmware update on page 33).
12. Declaration of Conformity Hiermit erklärt FichtelBahn, dass die Baugruppe „ReadyMagnet“ der Richtlinie 2014/30/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: www.fichtelbahn.de/declaration.html...