How To Save Parameters - gefran SIEIDrive ADV200 DC Series Quick Start Up Manual

●
The parameter may assume the number of another parameter as value.
T+
02 DRIVE INFO
03 STARTUP WIZARD
04 DRIVE CONFIG
05 REFERENCES
Pressing E, modifi cation mode is activated. The entire line is displayed in reverse.
The elements of the list of parameters associated to this parameter can be
scrolled using the ▲ and ▼keys.
Press E to confi rm the modifi cation or ESC to cancel.
●
The parameter may assume only the values contained in a selection list.
T+
01 MONITOR
02 DRIVE INFO
03 STARTUP WIZARD
04 DRIVE CONFIG
Pressing E, modifi cation mode is activated. The entire line is displayed in reverse.
The elements of the selection list can be scrolled using the ▲ and ▼ keys.
Press E to confi rm the modifi cation or ESC to cancel.
●
A parameter can be used to carry out a number of operations on the drive.
For an example, see
displayed instead of the value.
To perform the command, press E.
During execution of the command, the "In progress" caption is displayed to indi-
cate that the operation is in course.
At the end of execution, if the result is positive, the "Done" caption is displayed for
few seconds.
If execution has failed, an error message is displayed.

6.4 How to save parameters

Menu 04 DRIVE CONFIG, parameter 04.01 Save parameters, PAR : 550.
Used to save changes to parameter settings so that they are maintained also at
the power-off.
T+ T - EN LOC ILim n:0 AL
01 MONITOR
02 DRIVE INFO
03 STARTUP WIZARD
04 DRIVE CONFIG
To exit, press the ◄ key.
62
LINK type parameter
T - EN LOC ILim n:0 AL T+
0 5 . 0 4
Ram ref 1 src
Mlt ref out mon
Value:
ENUM type parameter
T - EN LOC ILim n:0 AL
Execution of commands
paragraph
T+ T- EN LOC ILim n:0
0 4 . 0 1 PA R : 5 5 0
Save arameters p
Press E to execute
ADV200 • Quick start up guide - Specification and installation
T- EN LOC ILim n:0 AL T+
PA R : 6 1 0 0 5 . 0 4
p
Ram ref 1 src
E
Mlt ref out mon
2034 Value:
T+ T- EN LOC ILim n:0 AL
X 2
0 4 . 0 3 PA R : 5 5 4
Access mode
Eas
Y
Value 0
6.4: in this case, the "Press E to execute" request is
AL T+ T- EN LOC
0 4 . 0 1
Save arameters p
E
In ro ress p g
T+ T-
0 5 . 0 4
p
Ram ref 1 src
Analo g in p ut 2 mon
Value:
T- EN LOC ILim n:0 AL
PA R : 6 1 0
p
852
T+ T-
0 5 . 0 4
p
Ram ref 1 src
M p ot out p ut mon
Value:
T+ T- EN LOC
0 4 . 0 3
Access mode
E
p
Ex ert
Value
ILim n:0 AL T+ T- EN
PA R : 5 5 0 0 4 . 0 1
Save arameters p
Done
EN LOC ILim n:0 AL
PA R : 6 1 0
1550
EN LOC ILim n:0 AL
PA R : 6 1 0
894
ILim n:0 AL
PA R : 5 5 4
1
LOC ILim n:0 AL
PA R : 5 5 0