Advertisement
ASSEMBLY
Brillion Elite Mini Monitor
IMPORTANT
The Brillion Elite Mini Monitor System by Loup
utilizes a MUX communication line. Sensors must be
learned into the Monitor. Location of each pre-learned
Smart Shaft Sensor or Bin Level Sensor is important
for proper Monitor display. Each Sensor utilizes 3
wires (+, -, MuxBus) to connect to the system. The
Harnesses do not require a specific Sensor
connection points. Each Sensor is identified in the
Monitor by its own signal.
Refer to Brillion Elite Mini Monitor Single Box Schematic.
See Figure 2-5.
WARNING
High Power Magnet in use. See "High Power
Magnet" on page 1-2.
IMPORTANT
All Harnesses must be firmly attached to Machine
Frame members so they do not sag or become torn
loose by field debris.
1. Lay out the Seeder Harnesses on the front of each
Seeder section ensuring that the Electric Clutch 2-Pin
Connector is on the left side.
2. Rear RH side of each Seeder Section has a Sensor
Mount mounted on two Seed Cups. Install a Smart
Shaft Sensor to the Sensor Mount with sensor
provided hardware and #8-32 Flange Locknuts.
Adjust the Smart Shaft Sensor so that it is 1/8" Max
away from the pre-assembled Spacer w/Magnet on
the Seed Shaft. See Figure 2-6. Connect the Smart
Seed Shaft Sensor to the Seeder Harness.
3. Each Seeder Section has a Bin Level Sensor Bracket
on the inside at either end. See Figure 2-7.
Determine the desired level for the alarm to be
indicated on the Brillion Elite Mini Monitor and
assemble the Bin Level Sensors to Bin Level Sensor
Brackets with sensor provided hardware and #8-32
Flange Locknuts. If more adjustment is needed, the
Bin Level Sensor Brackets can also be raised or
lowered to the desired seed level. Install Cord Grips
from the inside of the Seed Box out and secure with
supplied Locknut on the outside of the Seed Box. To
get the Sensor Connector outside the Seed Box, feed
the terminals through the Cord Grip. Install the
terminals into the 3-Pin Shroud labeled "A", "B" and
"C" as follows "A" White, "B" Black, "C" Green. Inside
the Seed Box, add enough slack to the Bin Level
Sensor Cord to allow for future adjustment of the
Sensor. Secure the Bin Level Cord by tightening the
Cord Grip Compression Nut. Connect both Bin Level
2-4
TABLE OF CONTENTS
Sensors to the Seeder Harness. See Figure 2-4.
Shroud Pin ID
3 Pin Shroud
Figure 2-4: Bin Level Sensor Bracket Wire Detail
4. LH Seeder Only, Install Pickup Switch Bracket with
the Clutch Shaft Bearing Carriage Bolts, Lock Washer
and Nut. See Figure 2-8. Place Actuator Assembly
onto the Clutch Shaft, secure with Actuator Assembly
Set Screw. Assemble Smart Shaft Sensor onto the
Pickup Switch Bracket with sensor provided hardware
and #8-32 Flange Locknuts. Adjust the Smart Shaft
Sensor so that it is an 1/8" Max away from the
Actuator Assembly. Connect the Ground Speed
Smart Shaft Sensor to the Seeder Harness.
5. RH Seeder Section does not require a Ground Speed
Smart Shaft Sensor, seal RH Seeder Section Seeder
Harness Connector with a 3-Pin Shroud and Cavity
Plugs to protect the Seeder Harness from the
environment.
6. Unused Main Harness 6 Pin Connector and both
unused Seeder Harnesses RH 3 Pin Connectors
need to be sealed with 6-Pin and 3-Pin Shrouds and
Cavity Plugs to protect the Harnesses from the
environment.
7. Orient the Main Harness so that the single 6-Pin
connector is to the front and the three 6-Pin
connectors are to the rear of the Folding Seeder
Frame. Route the Main Harness inside the Folding
Seeder Frame Main Tube.
8. Install Brillion Elite Mini Monitor on Tractor.
9. If not already installed, install Smart Clutch Relay into
Elite Mini Tractor Harness 3-Pin Connectors.
10. Connect the Elite Mini Tractor Harness 14-Pin
Connector to Brillion Elite Mini Monitor, 3-Pin Power
Plug to 12 Volt Tractor Convenience Outlet and 6-Pin
Connector to the Main Harness. 4-Pin Connector is
not used at this time.
11. Connect a 240" Extensions Harness to the RH and LH
Seeder Harnesses and connect both 240" Extension
Harnesses to the Main Harness.
12. Bundle and secure all Harnesses along the Seeder
Section Frames and Folding Seeder Frame with Tie
Wraps.
13. Program Bin Level Sensors and Smart Shaft Sensors
if not already pre-programmed. See "Brillion Elite
Mini Monitor" Chapter.
Terminal
White Wire
Black Wire
Seal
Green Wire
F-886-0322
Advertisement
