1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. Tilloll 875 Series
  6. Operator's manual

Landoll 875 Series Operator's Manual

Tilloll
Hide thumbs Also See for 875 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL 875 SERIES
TILLOLL
OPERATOR'S MANUAL
1900 NORTH STREET
MARYSVILLE, KANSAS 66508
(785) 562-5381
F-60-1099
10/99

Advertisement

Table of Contents
loading

Related Manuals for Landoll 875 Series

Summary of Contents for Landoll 875 Series

  • Page 1 MODEL 875 SERIES TILLOLL OPERATOR’S MANUAL 1900 NORTH STREET MARYSVILLE, KANSAS 66508 (785) 562-5381 F-60-1099 10/99...
  • Page 2 LANDOLL will not be liable for labor, transpor- tation, or any other charges resulting from replacement of a defective part. This warranty is void if any part not supplied by LANDOLL is used in assembly or repair, or if the machine has been altered, abused, or neglected.
  • Page 3 MODEL 875 SERIES TILLOLL OPERATOR’S MANUAL PURCHASED FROM: DATE ADDRESS: PHONE NO.: SERIAL NO.:...

  • Page 5: Table Of Contents

    TABLE OF CONTENTS SECTION DESCRIPTION PAGE NO. INTRODUCTION STANDARD SPECIFICATIONS ASSEMBLY INSTRUCTIONS FRAME ASSEMBLY - RIGID MODELS ..... 3-2 FRAME ASSEMBLY - 15’ FOLD MODEL ....3-3 FRAME ASSEMBLY - WING MODELS .
  • Page 6 SAFETY PRECAUTIONS THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL INJURY HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL TO AVOID POSSIBLE INJURY OR DEATH. DANGER DANGER INDICATES AN IMMINENTLY HAZARDOUS SITUA- TION WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

  • Page 7: Introduction

    INTRODUCTION The Landoll 875 Series Tilloll is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation. SECTION 1 gives basic instructions on the use of this manual.

  • Page 9: Standard Specifications

    STANDARD SPECIFICATIONS SIZE WIDTH TRANSPORT NO. OF NO. OF APPROX. OF CUT WIDTH SHANKS 20" DISC WEIGHT BLADES LBS. 875-10 10’-6" 12’-0" 5,059 875-13 13’-6" 15’-0" 5,753 875-15 15’-0" 16’-6" 6,090 875-15F 15’-0" 9’-4" 6,940 875-18 18’-0" 10’-6" 9,700 875-21 21’-0"...
  • Page 10 LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION).
  • Page 11 LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRI- .
  • Page 12 Figure 2-1 875-10 Shank Placement Assembly...
  • Page 13 Figure 2-2 875-13 Shank Placement Assembly...
  • Page 14 Figure 2-3 875-15 Shank Placement Assembly...
  • Page 15 Figure 2-4 875-15F Shank Placement Assembly...
  • Page 16 Figure 2-5 875-18 Shank Placement Assembly...
  • Page 17 Figure 2-6 875-21 Shank Placement Assembly...
  • Page 18 Figure 2-7 875-25 Shank Placement Assembly 2-10...
  • Page 19 NOTES: 2-11...

  • Page 21: Assembly Instructions

    ASSEMBLY INSTRUCTIONS DANGER It is very important that your new 875 Series Tilloll be properly assembled, adjusted and lubri- cated before use. Illustrations to assist with the as- DISC BLADES ARE EXTREMELY sembly process are provided in Section 2, “Stan- SHARP.

  • Page 22: Frame Assembly - Rigid Models

    Figure 3-1 Frame Assembly - Rigid Models 3-1 FRAME ASSEMBLY - RIGID MODELS IMPORTANT 3-1.4 Place frame assembly on stands ap- proximately 36" high. READ ALL SAFETY PRECAUTIONS AT THE 3-1.5 Install mast to frame using coulter sup- FRONT OF THE SECTION BEFORE ATTEMPT- port bars, 5/8-11 x 6 hex head cap screws, ING ANY OF THE FOLLOWING PROCEDURES.

  • Page 23: Frame Assembly - 15' Fold Model

    Figure 3-2 Frame Assembly - 15' Fold Model 3-2 FRAME ASSEMBLY - 15’ FOLD MODEL WARNING IMPORTANT READ ALL SAFETY PRECAUTIONS AT THE DO NOT ATTEMPT TO LIFT HEAVY FRONT OF THE SECTION BEFORE ATTEMPT- PARTS (SUCH AS THE FRAME, DISC ING ANY OF THE FOLLOWING PROCEDURES.
  • Page 24 Figure 3-3 Frame Assembly - Fold Models...
  • Page 25 Figure 3-4 Frame Assembly - Fold Models...
  • Page 26 Figure 3-5 Shank, Clamp, and Sweep Assembly...

  • Page 27: Frame Assembly - Wing Models

    3-3 FRAME ASSEMBLY - WING MODELS IMPORTANT 3-3.4 Connect wings to frame using hinge pin, 1" flat washers, and 1/4 x 2 cotter pins (See READ ALL SAFETY PRECAUTIONS AT THE Figure 3-4). FRONT OF THE SECTION BEFORE ATTEMPT- 3-3.5 Place frame and wing assembly on ING ANY OF THE FOLLOWING PROCEDURES.
  • Page 28 Figure 3-6 Hydraulic Lift Assembly - Rigid Models Figure 3-7 Hydraulic Lift Assembly - 15' Fold Model...

  • Page 29: Gauge Wheel Installation

    3-5 GAUGE WHEEL INSTALLATION 3-5.2 Mount the tires on the wheels and in- 3-5.1 All gauge wheel arms, rockshafts, and stall on the hubs. hubs come already assembled from the fac- Recommended tires: 11L X 15 10 ply tory. 3-6 HYDRAULIC LIFT INSTALLATION - RIGID AND 15’ FOLD IMPORTANT 3-6.2 Install the master cylinders (all models)
  • Page 30 Figure 3-8 Hydraulic Lift Assembly - Fold Models 3-10...

  • Page 31: Hydraulic Lift Installation - Fold Models

    3-7 HYDRAULIC LIFT INSTALLATION - FOLD MODELS IMPORTANT IMPORTANT READ ALL SAFETY PRECAUTIONS AT THE MOUNT CHECK VALVE SO THAT THE PORTS FRONT OF THE SECTION BEFORE ATTEMPT- V1 AND V2 ARE FACING THE DIVIDER VALVE ING ANY OF THE FOLLOWING PROCEDURES. WITH V1 PORT BEHIND THE V2 PORT.
  • Page 32 Figure 3-9 Hydraulic Fold Assembly - 15'F Model 3-12...

  • Page 33: Hydraulic Fold Installation - All Fold Models

    3-8 HYDRAULIC FOLD INSTALLATION - ALL FOLD MODELS IMPORTANT 3-8.2 Install short and flat wing supports on wings using u-bolts and 5/8-11 hex lock nuts. READ ALL SAFETY PRECAUTIONS AT THE Refer to Figures 2-1 through 2-7, 3-2, and FRONT OF THE SECTION BEFORE ATTEMPT- 3-4 for locations.
  • Page 34 Figure 3-10 Hydraulic Fold Assembly - 18’, 21’, 25’-6” Models 3-14...
  • Page 35 ITEM PART NO. HOSE LENGTH (MODEL USED) 1-397-010106 64" (18’) 2-397-010008 68" (21) 1-397-010026 78" (25’-6") 2-397-010009 86" (18’ & 21’) 1-397-010027 90" (25’-6") 1-397-010108 56" (18’ & 21’) 1-397-010106 64" (25’-6") 1-397-010082 36" (18’) 1-397-010104 50" (21’) 1-397-010108 56" (25’-6") 1-397-010083 28"...
  • Page 36 Figure 3-11 Disc Gang and Spray Shield Installation 18’, 21’, 25’-6" Models 3-16...

  • Page 37: Disc Gang And Spray Shield Installation

    3-9 DISC GANG AND SPRAY SHIELD INSTALLATION IMPORTANT IMPORTANT READ ALL SAFETY PRECAUTIONS AT THE DISC ROD AND SLOTTED NUT SHOULD BE FRONT OF THE SECTION BEFORE ATTEMPT- TIGHTENED TO A TORQUE OF 1200 FT. LB. ING ANY OF THE FOLLOWING PROCEDURES. THIS IS EQUIVALENT TO A 200 LB.
  • Page 38 Figure 3-12 Reel Assembly Installation 3-18...

  • Page 39: Reel Assembly Installation

    3-10 REEL ASSEMBLY INSTALLATION IMPORTANT IMPORTANT READ ALL SAFETY PRECAUTIONS AT THE DISTANCE BETWEEN REEL BLADE FRONT OF THE SECTION BEFORE ATTEMPT- SHANK SHOULD BE 1 INCH. ING ANY OF THE FOLLOWING PROCEDURES. 3-10.5 Reel bearings lock collars should be in- stalled as described below: 3-10.1 Loosely bolt center reel shank assembly...
  • Page 40 Figure 3-13 Harrow Assembly Installation 3-20...

  • Page 41: Harrow Assembly Installation

    3-11 HARROW ASSEMBLY INSTALLATION IMPORTANT 3-11.4 Install harrow springs and chains as shown in Figure 3-13 using 1/2-13 x 4 hex READ ALL SAFETY PRECAUTIONS AT THE head cap screws and hex lock nuts. The top FRONT OF THE SECTION BEFORE ATTEMPT- spring is anchored in the 1st hole from the ING ANY OF THE FOLLOWING PROCEDURES.
  • Page 42 Figure 3-14 Pull Hitch Installation - 15'F Model 3-22...

  • Page 43: Pull Hitch Installation - 15'F Model

    3-12 PULL HITCH INSTALLATION - 15’F MODEL IMPORTANT 3-12.1 Install pull hitch assembly to frame us- ing hitch pins and 1/4 x 2-1/2 cotter pins THE RADIUS ROD AFFECTS TWO ADJUST- (See Figure 3-14). MENTS: 3-12.2 Attach radius rod assembly to mast us- ing extended cylinder pin and 1/4 x 2 cotter IT LOCATES THE PULL HITCH CLEVIS AT THE pins.
  • Page 44 Figure 3-15 Pull Hitch Installation - All Other Models 3-24...

  • Page 45: Warning Lights Installation

    Figure 3-16 Electrical Installation 3-14 WARNING LIGHTS INSTALLATION 3-14.1 Assemble lights to the warning light bracket using 1/4-20 X 1-1/4 hex head cap IMPORTANT screws and hex lock nuts. Insure the wires are in the groove in the base of the light to- MAKE SURE LIGHTS ARE POSITIONED FOR ward the mounting surface on the bracket.
  • Page 46 Figure 3-17 Decal Installation (1 of 2) 3-26...
  • Page 47 Figure 3-18 Decal Installation (2 of 2) 3-27...

  • Page 48: Lubrication

    3-15 LUBRICATION The 875 Series Tilloll must be lubricated before using it for the first time, and at regular intervals thereafter. Use a standard multi-purpose grease. See Section 4-13 to lubricate your 875 Series Tilloll. 3-16 DECAL PLACEMENT Decals are extremely important for naming pur- poses and for alerting others to the presence of the machine.
  • Page 49 NOTES: 3-29...

  • Page 51: Operation And Maintenance

    DANGER DANGER NEVER ALLOW ANYONE TO RIDE ON ALWAYS LOCK THE TRACTOR DRAW- THE 875 SERIES TILLOLL AT ANY BAR IN THE CENTER POSITION WHEN TIME. ALLOWING A PERSON TO RIDE TRANSPORTING THE UNIT. FAILURE ON THE MACHINE CAN INFLICT SERI-...

  • Page 52: Tractor Preparation

    TRACTOR PREPARATION 4-1.1 Inflate the rear tractor tires equally and The Landoll 875 Series Tilloll is designed to be add ballast according to the tractor opera- pulled by tractor equipped with a double lip or cle- tor’s manual. vis type hitch. If your tractor is not equipped as 4-1.2...

  • Page 53: Attaching To The Tractor

    Figure 4-2 Transport Locks 4-3 ATTACHING TO THE TRACTOR b. Raise when the control arm is moved back- 4-3.1 Align the tractor drawbar with the ma- ward or upward. chine. Raise or lower the Tilloll ring hitch, as 4-3.3 Fully extend the hydraulic gauge wheel needed, using the swivel jack.

  • Page 54: Transport

    4-4 TRANSPORT IMPORTANT 4-4.1 Raise the unit to full transport height. 4-4.2 Fold the wings. WHEN TRANSPORTING FARM IMPLEMENTS IMPORTANT ON PUBLIC ROADS, IT IS THE RESPONSIBIL- ITY OF THE OPERATOR TO ABIDE BY STATE WHEN FOLDING OR UNFOLDING WINGS, OP- AND LOCAL LAWS CONCERNING WIDE LOAD, ERATE TRACTOR ENGINE AT A SLOW IDLE SPEEDS, AND SAFETY LIGHTING EQUIPMENT.

  • Page 55: Disc Gang Scraper Adjustment

    CAUTION DRIVE AT REASONABLE SPEEDS TO INSURE YOUR SAFETY. SLOW DOWN BEFORE MAKING SHARP TURNS OR USING THE BRAKES. DRIVE SLOWLY OVER ROUGH GROUND, SIDE HILLS, AND AROUND CURVES TO AVOID TIP- PING. 4-5.2 Check the front to rear leveling of the frame.

  • Page 56: Spray Shield Adjustment

    4-7 SPRAY SHIELD ADJUSTMENT 4-7.3 The shields should also be set at an an- 4-7.1 The spray shields directly behind the gle to carry some soil back to the center of disc gang have two uses and can be ad- the machine as it levels the soil.

  • Page 57: Harrow Adjustment

    Figure 4-5 Harrow Adjustment 4-10 HARROW ADJUSTMENT 4-10.1 The harrow on the rear of the machine c. Spring tension can be increased by lowering can be set for a variety of field conditions. the rear mounting point of the two lower The harrow that is set up according to the springs and raising the front mounting point of assembly instructions for a working depth of...
  • Page 58 Figure 4-6 Lubrication Points LUBRICATION ITEM DESCRIPTION NO. OF INTERVAL LUBE POINTS (Hours unless stated) Radius rod Gauge wheel pivot pin Disc gang bearing Reel bearing Yearly Walking beam Yearly Wheel bearing NOTE: LUBE ALL POINTS WITH HIGH GRADE MULTI-PURPOSE GREASE. Table 4-1 Lubrication Schedule...

  • Page 59: Wheel Bearing Maintenance

    Table 4-1 and Figure 4-6 specifies the good status. number and the period of lubrication points on the 875 Series Tilloll. Proper mainte- nance of your machine will, under normal op- erating conditions, help to keep it operating at or near its peak performance for an ex- tended period of time.
  • Page 60 NOTES 4-10...

  • Page 61: Troubleshooting Guide

    TROUBLESHOOTING GUIDE The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can hap- pen using your 875 Series Tilloll. Follow all safety precautions stated in the previous when making any ad- justments to your machine.
  • Page 62 PROBLEM PROBABLE CAUSE:SOLUTION 5. PLUGGING BETWEEN DISC AND SPRAY A. Dirt Not Flowing Under Shield: Readjust spray SHIELD shield (usually up and/or to the rear). Machine running too deep. Raise to proper operating depth by adjusting stroke control depth stop on master cylinder. B.
  • Page 63 PROBLEM PROBABLE CAUSE:SOLUTION 13. REEL NOT MOVING SOIL ADEQUATELY A. Reel Mounted Backwards: Mount again per assembly instructions. B. Running Machine Too Slow: Machine needs to be pulled at least 5.5 mph. C. Machine Not Level: Adjust radius rod to level machine.
  • Page 64 NOTES:...

This manual is also suitable for:

875-10875-13875-15875-15f875-18875-21 ... Show all

Table of Contents