Komatsu PC138US-11 Operation & Maintenance Manual page 457

Hydraulic oil temperature caution lamp................... 3-24
Hydraulic oil temperature gauge .............................. 3-39
Hydraulic system - Warm-up .................................. 3-161
Hydraulic system caution lamp ................................ 3-25
Hydraulic tank - Change oil ....................................... 4-76
Hydraulic tank - Check oil level / Add oil ............... 3-132
Hydraulic tank breather element - Replace ............ 4-62
Hydraulic tank strainer - Clean ................................. 4-64
If any problem is found .............................................. 2-19
If machine monitor shows warning display ........... 3-245
Indicator - Check electrolyte level ............................ 4-45
Inducement Strategy for abnormalities recurrences
within 40 hours ................................................. 3-127
Inducement strategy when abnormalities are detected
in the Urea SCR System devices .................. 3-121
Inducement strategy when the DEF tank Level be-
comes low. ........................................................ 3-118
Inside operator's compartment ................................. 2-19
Inspecting machine .................................................... 2-18
Introduction ................................................................... 1-8
Investigate and confirm jobsite conditions .............. 2-26
Jumper cable - Connect .......................................... 3-240
Jumper cable - Disconnect ..................................... 3-241
KCCV filter element - Replace ................................. 4-68
KCCV hose - Replace ............................................... 4-76
Keep machine clean .................................................. 2-18
Keep work place clean and tidy ............................... 2-40
Komatsu Closed Crankcase Ventilation (KCCV).3-112
Komatsu genuine lubricants ....................................... 4-2
Komatsu genuine replacement parts ........................ 4-2
KOMTRAX ................................................................ 3-128
KomVision. .................................................................. 6-38
Lamp switch. ............................................................... 3-88
Language settings ...................................................... 3-79
Large capacity final drive case - Change oil .......... 4-58
Large capacity final drive case - Check oil level / Add
oil .......................................................................... 4-42
Left front mirror - Adjust. ......................................... 3-146
Leveling work ............................................................ 3-188
Lifting objects with buckets ....................................... 2-38
Lifting of personnel prohibited .................................. 2-22
Lightweight towing hole - Precautions ................... 3-236
Loading and unloading with trailer ......................... 3-220
Loading work............................................................. 3-188
Location of engine serial No. plate .......................... 1-12
Location of product identification number (PIN)/
machine serial No. plate.................................... 1-12
8-4
I
J
K
L
Lock. .......................................................................... 3-194
Lock inspection cover ...................................................4-3
Lock lever ................................................................... 3-94
Lock lever automatic lock cancel switch ................. 3-90
Lock pin........................................................ 3-97,6-17
Low register range (bass) - Adjust ........................ 3-215
Lower wiper switch .................................................... 3-91
Lubrication chart ...........................................................7-4
Machine - Check walk-around ............................... 3-129
Machine - Escape from mud .................................. 3-186
Machine - Escape when track on one side is stuck.....
..................................................................... 3-186
Machine - Escape when tracks on both sides are
stuck. ................................................................. 3-187
Machine - Lift. ........................................................... 3-227
Machine - Load ........................................................ 3-221
Machine - Lubricate ................................................... 4-47
Machine - Operate when working mode display does
not display either ATT/P or ATT/E of attachment
mode .................................................................... 6-28
Machine - Operate when working mode is not in
breaker mode ..................................................... 6-26
Machine - Park ......................................................... 3-192
Machine - Raise using block .................................... 4-36
Machine - Running-in the new machine ............... 3-159
Machine - Secure .................................................... 3-223
Machine - Set at angle .............................................. 4-35
Machine - Set by using slope ................................... 4-35
Machine - Start (Travel forward and reverse) / Stop....
..................................................................... 3-169
Machine - Start after long-term storage ................ 3-232
Machine - Steer (Change the direction) ............... 3-172
Machine - Stop ......................................................... 3-171
Machine - Store long-term ........................................ 6-29
Machine - Swing ...................................................... 3-174
Machine - Travel forward ........................................ 3-170
Machine - Travel reverse ........................................ 3-170
Machine - Unload .................................................... 3-225
Machine - Warm-up operation ............................... 3-166
Machine equipment - Names ......................................3-2
Machine monitor - Operate when operator identifica-
tion function is available with skip .................... 3-80
Machine monitor - Operate when operator identifica-
tion function is available without skip .............. 3-82
Machine monitor - Operate when starting engine in
normal situation ................................................... 3-11
Machine monitor - Operate when starting switch is
ON while operator ID input is set ..................... 3-13
Machine monitor equipment name................. 3-6,6-38
Machine operations and controls .......................... 3-129
Machine ready for installation of attachment - Handle.
....................................................................... 6-16
Machine settings ........................................................ 3-66
Magazine box ........................................................... 3-105
Main use of machine ....................................................1-8
WENAM00111
INDEX
M