Key Fob Transmitters; Dealer Code - NAPCO Gemini GEM-P1632 Programming Instructions Manual

Page 16
(Direct Entry)
(Direct Entry)
(Direct Entry)
bottom buttons must be depressed to activate an alarms. In this case, the
Aux-1 and Aux-2 cannot be programmed.
Press to save. Press NEXT (
Key Fob Zone Assignment (refer to display as shown on the previous page: press the (
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 = point
3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs (using 2 buttons) or 8 key fobs (using all 4 buttons) or any
combination up to a maximum of 32 controlled zones can be assigned, providing multiple wireless panic buttons on a
system, each reporting to the Central Station or a pager and/or annunciating on a keypad the key fob zone number with
description/location. To assign a key fob to a zone: program the keyfob as you would a transmitter, entering the keyfob's
ID code, check sum and point number at the appropriate zone. The "Quick Method" is not allowed. The zone may be
hardwired to a sensor as well as assigned to a key fob (either one will activate the zone alarm output). NOTE: If assigning
a key fob to a zone, the "ON/OFF" buttons on the key fob will no longer arm/disarm the system. The key fob is converted
to a "panic only" device.
ZONE DESCRIPTIONS: GEM-RP2ASe2 cannot be used to enter Zone Descriptions. To enter Zone Descriptions you
must use the GEM-RP1CAe2 Keypad or the Napco Quickloader Software.
(Direct Entry)
(Direct Entry)
EXIT DEALER PROGRAM MODE: This completes the custom default program. Press the


Direct Address Program Mode for further programming or press the
resume normal keypad operation.
CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode,
press the button to enter the Address Program Mode; (b) access Location 1197 (Clear Program); (c) press
start over.
GEM-P1632 Programming Instructions
Key Fob Transmitters (Press the (
Keyfobs can be programmed as "Arm/Disarm" devices using their buttons
(refer to WI752). For each Key Fob Transmitter, enter:
the Key Fob Transmitter number (01–08).
area number to which transmitter is assigned (1 or 2); enter 0 to disable
keyfob.
the 6-digit RF ID # printed on the transmitter (enter all numbers and/or
letters, including leading "0"s, if any).
1-digit checksum number printed on the transmitter (enter all numbers
and/or letters, including leading "0"s, if any).
Aux-1 Option (see key fob
aux 1 & aux 2 options).
Aux-2 Option (see key fob
aux 1 & aux 2 options).
Note: If the Key Fob is con-
verted for
"Emergency Use" (by cutting

an internal jumper), both top or
) button to proceed.

Dealer Code

Directly enter the Dealer Code (default = 456789), including leading zeros.
Use the
zero. Press
Re-enter the Dealer Code to verify the previous code. Press
Press NEXT (
DATA
ENTRY
•(blank)
1
2
3
Two Button
4
5
6
through buttons. NOTE: Pres the
to save.

) button to proceed.


button once again to end all programming and
WI897B 8/98
) button to set cursor.)
AUX 1/AUX 2 DATA AUX 1/AUX 2 OP-
OPTIONS ENTRY TIONS
None 7 Relay Group 7
8 Relay Group 8
Relay Group 1
9 Keypad Panic
Relay Group 2
0 Aux K.P. Panic
Relay Group 3
B Instant
Relay Group 4
C Toggle Aux Relay
Relay Group 5
Relay Group 6
) button to go backwards.)

button for a


button to enter the
NAPCO Security Systems
to save.
and