Torque Unit Codes - Imada HTGS-4 Instruction Manual

4.Command Table
(RS232C & USB communication)
CATEGORY COMMAND
XAR[CR]
XFP[CR]
Data Output XFF[CR]
Data Output
XAg[CR]
XAG[CR]
XAS[CR]
XCW XCW[±UUUU][±LLLL][CR]
Comparator
Setpoints
XCR
XCR[CR]
XDS0[CR]
Mode XDS1[CR]
Mode
XDS2[CR]
XDS3[CR]
XFU0[CR]
XFU1[CR]
Unit XFU2[CR]
Unit
XFU[3~5][CR]
XFC
XFC[CR]
XFT
XFT[bbbb][CR]
Peak
Peak
XFG0[CR]
XFG1[CR]
XFY[CR]
Reset
Reset XFZ[CR]
XAZ[CR]
XMM[CR]
Memory XMR[CR]
Memory
XMC[CR]
XME[CR]
Counter XCN[CR]
Counter
XCC[CR]
Power XQT[CR]
Other
5.Data Output Formats
Data Output Format [Q][±fffff][±ddddddd][P][L][C][S][X][CR]
Memory Data Output Format m[±fffff][±ddddddd][P][L][C][S][YY][MM][DD][hh][mm][ss][CR]
page 16
DESCRIPTION
Real Time Data Output Request
+Peak and –Peak Data Output Request
1st Peak and 2nd Peak Data Output Request
Continuous Data Output Request (10 data/sec)
Continuous Data Output Request (2000 data/sec)
Stop Continuous Data Output
Set High/Low Comparator Set High/Low Setpoints
High/Low Comparator Output Request
High/Low Setpoint Output Request
Switch Mode
Switch Mode
Switch Unit
Switch Unit
List of Measuring Unit Output Request
List of Measuring Unit Output Request
Set 1st and 2nd Peak Sensitivity
Set 1st and 2nd Peak Sensitivity
Peak Switch Function Select
Peak Switch Function Select
Reset Peak
Tare
Reset All (Peak and Tare)
Save Data in Memory
Download All Memory Data Request
Clear All Memory
Clear Last Memory
+NG Counter data output request
Clear +NG Counter
Turn off Power
Invalid command
RESPONSE NOTES
See Data Output Format
USB connection only
R[CR]
±UUUU: High Setpoint
R[CR] R[CR] ±LLLL: Low Setpoint
(w/o decimal point)
XCRH[CR] Display > High Set
High ≥ Display ≥ Low
XCRO[CR]
Display < Low Setpoint
XCRL[CR]
XCRE[CR] Overload
Real Time Display
Peak Display
R[CR]
+Peak Display
–Peak Display
Unit0
Unit1
R[CR]
Unit2
Unit3 - 5 (Option)
00 - 55: Unit Code for Unit 0 - 5
XFC[00][11][22][33][44][55][CR]
00 - 55: Unit Code for Unit 0 - 5 (See Unit Code Table)
(See Unit Code Table)
XFT[bbbb][CR] bbbb: Peak Sense Drop Digits
R[CR]
(w/o decimal point)
Real Time, +Peak, –Peak (Functions cycle)
R[CR]
Real Time, Peak (Functions toggle)
R[CR]
R[CR]
See Memory Data Output Format
R[CR]
R[CR]
XCN[nnnn][CR] nnnn: Number of +NG
R[CR]
R[CR]
E[CR]

6.Torque Unit Codes

TORQUE UNIT CODES
CODE 00 01 02 03 04 05 07 08 10 11 12
UNIT None mN N kN g kg gf kgf ozf lbf klbf N-cm N-m kgf-cm kgf-m ozf-in lbf-in
(See XFC command to get unit info.)
13 14 16 17 22 23
page 17