Table of Contents
Advertisement
SP+ Series Programming Guide
Communicator
Step Action
1
+ installer code
2
2 = backup phone #
3 = personal phone #1
4 = personal phone #2
3
5 = personal phone #3
6 = personal phone #4
7 = personal phone #5
4
Phone # +
ENTER
Cancel Communication
Step Action
1
+ installer code
2
3
9
Keypad Programming
Assigning Keypad Zone Numbers
Step Action
1
E
+ installer code
NTER
Press and hold
for
2
three seconds
3
Zone number +
ENTER
NOTE: To erase a keypad zone number, press
Assigning Keypad Zone Numbers TM50/TM70
Step Action
Press and hold
MENU
1
+ installer code
2
Program this unit
Press keypad zone
3
number
Entry Point Zone Assignment (StayD)
Step Action
1
E
+ installer code
NTER
Press and hold
for
OFF
2
three seconds
3
Zone number
4
E
NTER
Details
= flash; maintenance code may also be
used
-
Enter phone number (up to 32 digits), and
then press
to proceed to the next phone
ENTER
number, or go to step 5 if option 8 was
selected
Details
= flash; maintenance code may also be
used
-
Cancels all communication with BabyWare and
PCS module
Details
+
= flash; maintenance code may
ARM
STAY
also be used
+
= ON
ARM
STAY
K35, K32, K32LCD, K32LX = two digits: 01 to 32;
K636, K10V/H = one digit: 1 to 0 (10)
, and then
CLEAR
ENTER
Details
Enters into advanced programming
Ensure that zone temperature input is enabled
Select your zone
Details
+
= flash
ARM
STAY
+
= ON
ARM
STAY
K35, K32RF, K37, K32LCD, K32LX = two digits:
01 to 32; K636, K10V/H = one digit: 1 to 0 (10;
maximum ten zones); the first zone
programmed will be the designated entry
point and will flash; up to three more path
zones can be added – these zones will light up
and remain lit
Press
to save and exit
ENTER
Keypad Input/Output Configuration (K636 V2.0 and higher)
Step Action
1
E
+ installer code
NTER
Press and hold
2
for three seconds
3
Option 1
4
Option 2
NOTE: When configuring as an output, clear the assigned keypad zone first.
PGMs
Step Action
1
+ installer code
2
3
PGM number
4
Enroll or erase PGM
5
PGM type
.
If PGM type is 1, 2, 3, or
4, enter activation
delay
6
If PGM type is
to the next available
PGM
If PGM type is
1
enter
and/or
If PGM type is
enter two-digit remote
control #
If PGM type is
7
two-digit zone #
If PGM type is
2
and/or
+
NOTE:
To erase a PGM, press and hold
Details
+
= flash
ARM
STAY
ENTER
+
= ON
ARM
STAY
ON = output switches to ground following
system arming (blue wire, maximum150 mA)
OFF = input (keypad zone input)
ON = output N.C.
OFF = output N.O.
Details
= flash; maintenance code may also be
used
-
Two digits: 01 to 16
Wireless PGM = press the
or remove and re-install Jumper 2 (JP2) on
module; hardwired PGM = press
1 = Follow button
2 = Follow button
3 = Follow zone
4 = Follow alarm
5 = Follow bell
6 = Follow arm
7 = Follow Stay arm
8 = Follow Sleep arm
1 = Follow
2 = 1 sec.
3 = 5 sec.
4 = 15 sec.
5 = 30 sec.
6 = 1 min.
7 = 5 min.
8 = 15 min.
9 = 30 min.
5
, proceed
-
If system is partitioned, select partition(s), and
6
7
8
,
, or
,
then press
to proceed to the next available
ENTER
2
+
ENTER
PGM
1
2
or
,
01 to 32 (00 = all remote controls); the control
panel proceeds to the next available PGM
3
, enter
01 to 32 (00 = all zones); the control panel
proceeds to the next available PGM
If system is partitioned, select partition(s), and
4
1
, enter
then press
to proceed to the next available
ENTER
ENTER
PGM
for three seconds.
SLEEP
/
switch
LEARN
TAMPER
ENTER
or
or
7
Hide quick links:
Advertisement
Table of Contents
