Paradox SP5500+ Programming Manual page 13

SP+ Series Programming Guide
Zone Definitions
NOTE: If a device is assigned to a zone which is already programmed, a wireless zone will overwrite a keypad/hardwire zone and a keypad zone will overwrite a
hardwire zone.
To define zones on your SP+ control panel:
1. Press , and then enter your installer code (maintenance code may also be used). The
ENTER
2. Enter the three-digit zone number you wish to program (e.g., 001 to 032). The
3. Enter a two-digit zone definition, by referring to table 4.
4. Assign a partition, by referring to table 5. By default, all zones are assigned to partition 1.
5. Select or deselect zone options, using buttons 1 to 8 (see tables 6 and 7).
6. Press to save and proceed to the next zone.
ENTER
7. Repeat steps 3 to 6 for all remaining zones.
Table 4: Zone definitions for SP+ Series panels
Input Value
00 Disabled (default)
01
02
03 Entry delay 1 (Full Arm)
04 Entry delay 2 (Full Arm)
05
06 Follow (sleep/full arm)
07 Follow (full arm)
08
09 Instant (sleep/full arm)
10 Instant (full arm)
11
12
13 Instant fire silent†
14 Delayed fire silent†
15
16
17
18
19
20
21
22
23 Follow no pre-alarm
24 Instant no pre-alarm
25 Keyswitch maintain**
26 Keyswitch momentary**
33 Instant no pre-alarm (stay/sleep)
34 Instant no pre-alarm (sleep)
35 Entry delay 1 (stay/full)/instant Entry delay 1
36 Entry delay 1 (full arm)/instant
* Flex-instant: zone will follow the delay at section [720] (default is 15 seconds/0 = instant zone).
** On-board, hardwire, control panel zones only.
† ZX8/ZX82 inputs do not support fire zones. For two-wire smoke installations these definitions apply to
zone 1 input only. Section [706], option 3, must be enabled. For four-wire smoke installations, use any panel,
on-board zone input.
‡ This alarm will follow the panic 1 option (section [702], option 1).
Description
Stay Arm
-
Entry delay 1 Entry delay 1
Entry delay 2 Entry delay 2
Not armed
Not armed
Follow Follow*
Not armed
Not armed
Instant Instant*
Not armed
Not armed
Instant fire† -
Delayed fire† -
-
-
24 hr. buzzer -
24 hr. burglary -
24 hr. hold-up -
24 hr. gas -
24 hr. heat -
24 hr. water -
24 hr. freeze -
24 hr. panic‡ -
-
-
-
-
Instant
Not armed
Instant
ARM
and functions will remain illuminated.
ARM STAY
Arming Type
Sleep Arm Fully Arm
- -
Entry delay 1 Entry delay 1
Entry delay 2 Entry delay 2
Not armed Entry delay 1
Not armed Entry delay 2
Follow* Follow
Follow* Follow
Not armed Follow
Instant* Instant
Instant* Instant
Not armed Instant
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
Instant Not armed
Instant Not armed
Instant Entry delay 1
Instant Entry delay 1
and functions will flash.
STAY
Table 5: Partition assignment for SP+ Series panels
Input Value
1 Assign to partition 1
2 Assign to partition 2
3 Assign to both partitions
NOTE: When using the K636 keypad, only
partition 1 is available.
Table 6: Zone options for SP+ Series panels
Input
Description
Value
1 Auto zone shutdown
2 Bypassable zone
3 RF zone supervision
6 Intellizone
7 Delay alarm transmission
8 Force zone
Input Value
4 5
OFF OFF
OFF ON
ON OFF
ON ON
NOTE: For additional zone options, see Zone
Options on page 37.
Table 7: Keyswitch options for SP+ Series panels
Input
Description
Value
1
2
3
OFF = Disarm; ON = Disarm only
4
if Stay/Sleep armed
5
6 Stay arming*
7 Sleep arming*
8
* Select only one. If all are OFF, keyswitch will
regular arm.
Description
Zone Alarm Type
Audible alarm
Pulsed alarm
Silent alarm
Report only
-
-
-
Arm only
-
13