Brief Table Of The Programs Installed - Smeg GW2145 User Manual

4.6

BRIEF TABLE OF THE PROGRAMS INSTALLED

For details of the various washing program phases, always refer to the enclosed
GW4190 Program Table"; the brief table below is purely guideline. The programs listed below may be subject to
modification for the purposes of improvement.
PROGRAMS with THERMAL DISINFECTION
In programs normally used in GW Glassware Washers, thermal disinfection takes place at the
beginning of the washing cycle, for the most effective removal of contamination and grease from
the material for processing.
This process is different from the one used and recommended in Hospital Instrument Washers,
where this phase concludes the cycle so that the instruments are maintained in a disinfected state.
CUSTOM PROGRAMS
The Custom programs are programs which can be modified to meet specific requirements.
Programs can only be modified using the Smeg TRACELOG software; contact Smeg for
information concerning the use and installation of the program.
ID
PR 1
PR 2
PR 3
PR 4
PR 5
PR 6
PR 7
PR 8
PR 9
PR 10
PR 11
PR 12
PR 13
PR 14
PR 15
PR 16
DEFAULT DETERGENT DOSES AND WATER INTAKES
P1 = 5ml/litre – alkaline detergent
P2 = 3ml/litre - acid
P3 = 10ml/litre - degreasing
a
P2 = 4ml/litre (non-standard P2 doses used in special
cases).
Water intake per phase, default = 9 litres
MAINS WATER - DEMINERALISED WATER in PROGRAMS
The enclosed table indicates when a specific phase takes in cold water and when demineralised
water.
If demineralised water is deselected by means of the appliance setup parameters, the appliance
will always take in cold water.
Whenever possible, connection to demineralised water is recommended, for better final rinsing
results and to avoid the formation of limescale.
User Manual
GW - GLASSWARE WASHER
Prewash
Plastics 75°C [ + Drying ]
Standard glassware 80°C [ + Drying ]
Intensive glassware 90°C [ + Drying ]
Agar Intensive glassware 93°C [ + Drying ]
Thermal disinfection 93°C – 3 minutes [ + Drying ]
Thermal disinfection 93°C – 10 minutes [ + Drying ]
Thermal disinfection + intensive wash 93°C – 5 minutes [ + Drying ]
Thermal disinfection + intensive wash 93°C – 10 minutes [ + Drying ]
Custom 1 (default: Petroleum Grease, 93°C – 1 minute) [ + Drying ]
Custom 2 (default: Mineral Oil, 93°C – 10 minutes [ + Drying ]
Custom 3 (default: Petrol, 93°C – 5 minute) [ + Drying ]
Custom 4 (default: Diesel, 93°C – 1 minute) [ + Drying ]
Custom 5 (default: Intensive Petrol, 93°C – 10 minutes [ + Drying ]
Custom 6 (default: Appliance auto-disinfection 93°C – 1 minute) [ + Drying ]
Service - operation of peristaltic pumps, intake of detergent + rinsing
Tab. 1 – Brief table of the programs installed
Tab. 2 – Brief table of doses and water intakes per phase.
GW2145 - GW1160 - GW4060 - GW4190
"GW2145-GW1160-GW4060-
FOR SERVICE PROGRAM ONLY,
AD HOC DETERGENT DOSES AND WATER INTAKES
P1 = 12ml/litre
P2 = 12ml/litre
P3 = 12ml/litre
a
P2 - Parameter not used in the Service program.
Water intake, phase 1 and phase 2 = 6 litres
Water intake, phase 3 = 9 litres
Page 25 - 86