Related Manuals for Smeg GW2045
Summary of Contents for Smeg GW2045
- Page 1 IN STRUC TION MANUA L Laboratory Equipment Pty Ltd email: sales@labec.com.au Ph: 02 9560 2811 • Fax: 02 9560 6131 www.labec.com.au 2014...
- Page 2 GW2045 GW1060 GLASSWARE WASHER OPERATING INSTRUCTIONS MANUAL...
- Page 3 This manual is for informational purposes only. The contents of this manual and the appliance described herein may be liable to modification without prior notice. In no case may SMEG be held liable for any direct or accidental damages deriving from or concerning the use of this manual.
- Page 4 Authorized Assistance Centre if necessary. instruments@smeg.it Fax +39 0522 821 593 Tel +39 0522 8211 You can examine our entire product range in our Internet web site: www.smeg-instruments.com International customers, please contact your local SMEG distributor.
-
Page 5: Table Of Contents
7.3. USING THE DETERGENT DISTRIBUTOR................... 32 7.4. LOADING NEUTRALISER ........................33 7.5. OPTIONAL ACCESSORIES ......................... 34 7.5.1. PERISTALTIC PUMPS P1 AND P3 (ACCESSORY “SMEG ADU”) ..........34 7.5.2. DETERGENT CAN LEVEL SENSORS..................35 7.6. PRECAUTION WHEN USING DETERGENTS..................36 ALARMS............................... - Page 6 9.2. IF THE GLASSWARE WASHER IS NOT USED FOR A LONG PERIOD OF TIME ......41 9.3. REUSING THE GLASSWARE WASHER AFTER A LONG STANDSTILL PERIOD ......41 9.4. TROUBLESHOOTING .......................... 41 INSTALLATION DIAGRAM GW2045 – GW1060................42 Rev. 00 GW2045 – GW1060 Manual...
-
Page 7: Introduction
In addition to being the cause of cancellation of any warranty cover, any repairs carried out by non-authorised staff may be a source of danger for the user. The machine must only be used by specifically trained persons. It is Smeg’s task to train the designated users when the appliance is installed. -
Page 8: Key To The Symbols Used In The Manual And On The Machine
Warning, danger: consult the manual Attention, hot surface. Alternating current. CE labelling. At the end of life the product should be sent to disposal facilities for the recovery and recycling. Rev. 00 GW2045 – GW1060 Manual Pag. 7 di 43... -
Page 9: General Recommendations
Only authorized and well-informed personnel are allowed to use the machine. Rev. 00 GW2045 – GW1060 Manual Pag. 8 di 43... -
Page 10: General Specifications
4. GENERAL SPECIFICATIONS 4.1. TECHNICAL FEATURES ELECTRICAL POWER SUPPLY GW2045 YPE OF OLTAGE 230V ~ [tolerated variation ± ± ± ± 10%] REQUENCY OWER ATING ELECTRICAL POWER SUPPLY GW1060 GW1060 GW1060 GW1060-3 GW1060-1 ODELS Triphase 400V Triphase 230V Monophase 230V... - Page 11 GLASSWARE WASHER MEASUREMENTS EIGHT GW2045: 620mm – GW1060: 670mm EPTH GW2045: 450mm – GW1060: 600mm IDTH NET WEIGHT [kg] GW2045: 50kg – GW1060: 65kg Material used Washing tub AISI 316L Outer coating AISI 304 ENVIRONMENTAL CONDITIONS Indoors Up to 1000 metres LTITUDE From 5°...
-
Page 12: Lifting And Handling
(see section below). fig. 1 – Front of the GW2045. To unlock the door it is necessary to: Turn on the machine (ON/OFF symbol), 2 – Press the button with the KEY symbol (first button on left) and wait a few seconds. -
Page 13: Emergency Unlocking Of Door
The appliance has a manual door opening device: a rubber ring with a cable that works directly on the locking device hidden in the centre of the lower part of the door. To open the door manually: pull the rubber ring downwards gently until the door clicks open. Rev. 00 GW2045 – GW1060 Manual Pag. 12 di 43... -
Page 14: Unlocking Gw1060
2 – Force the opening mechanism, pushing upwards. Insert a screwdriver into the slot behind the handle and press gently until the mechanism clicks. The area is marked by the arrow in the picture below. Rev. 00 GW2045 – GW1060 Manual Pag. 13 di 43... -
Page 15: Installation
Correct levelling will ensure that the machine operates in the right way. 5.3. CONNECTION TO WATER MAINS See section "INSTALLATION DIAGRAM GW2045-GW1060” at the back of the manual. Notes for preventing risks of blockage or damage: If the water pipes are new or have not been used for a long time, check that the water is clear and clean before attaching to water mains. - Page 16 DW: DEMI WATER: Inlet connection for demineralised water. GW2045 fig. 4 – rear of product GW2045, detail of rear cross-section with indication of water inlets and outlets. The appliance is standard equipped with 1 peristaltic pump for detergent dosage P2. P1 is an optional accessory.
-
Page 17: Non Pressurized Demineralized Water Connection
We advise having the PAD installed by a specialized SMEG technician. WARNING – WHEN INSTALLING THE PAD, MAKE SURE THAT: Make sure that the demineralized water pressure is less than 1bar. Smeg declines all responsibility if the PAD is installed with the inlet water at a higher pressure. -
Page 18: Water Outlet Connection
The outlet must comply with international legislation. Our company will accept no liability for pollution caused by improper use of the machine. Fig. 7 – adaptor with rubber holder for ½” pipe. Rev. 00 GW2045 – GW1060 Manual Pag. 17 di 43... -
Page 19: Electrical Connection
Refer to the technical features diagram for electrical absorption in the section "GENERAL SPECIFICATIONS ". GW2045 - The machine is designed for connection to an electricity main with the following voltage rating: • ~ 230V 1 / N / PE... -
Page 20: Description Of Controls
“LACK OF SALT” INDICATOR LIGHT "HEATING ON" INDICATOR LIGHT SIGNS ON THE FRONT OF THE MACHINE Door unlocking ON / OFF ° C Temperature Salt Lack ► ll START / PAUSE Heating element on Rev. 00 GW2045 – GW1060 Manual Pag. 19 di 43... -
Page 21: Setup Mode Description
IF YOU WISH TO EXIT THE SETUP MODE WITHOUT SAVING the parameters you may have • changed, do not press the DOOR OPENING (6) button, but turn off the machine using the ON/OFF button (3). Rev. 00 GW2045 – GW1060 Manual Pag. 20 di 43... - Page 22 It is possible to access and change the following parameters using programme selection and the buttons (5) and (4): Inactive Inactive Setup field Year month Time Minutes Seconds position position Switch position Rev. 00 GW2045 – GW1060 Manual Pag. 21 di 43...
-
Page 23: Washing Programme Settings
PR-4: Washing + thermo-disinfection at 90° C for 3’ (A0 =1800). PR-5: Washing + thermo-disinfection at 93° C for 10’ (A0 =12000). PR-6: CUSTOM 1, personalised programme set by authorised SMEG technicians on customer’s request (default: the programme carries out wash + thermo-disinfection at 93° for 3’). -
Page 24: Preparation Of Load For The Washing And Disinfecting Phase
Avoid direct and repeated contact with dirty instruments as much as possible. Always use extreme caution. Use all the individual protective devices available for this type of operation, before and after treatment. Rev. 00 GW2045 – GW1060 Manual Pag. 23 di 43... -
Page 25: Programmes Description
6.6. PROGRAMMES DESCRIPTION Rev. 00 GW2045 – GW1060 Manual Pag. 24 di 43... - Page 26 PERSONALISABLE PROGRAMMES 6 AND 7 Programmes 6 and 7, CUSTOM 1 and CUSTOM 2 respectively, can be personalised by authorised SMEG technicians, on the customer’s request. By default, programme 6 corresponds to “thermal disinfection at 93° C for 3’ ”.
- Page 27 BLANK TABLE FOR RECORDING ANY PERSONALISED PROGRAMMES Rev. 00 GW2045 – GW1060 Manual Pag. 26 di 43...
-
Page 28: Carrying Out The Programme
Wait for the end of the process without forcing the door. The automatic opening/non-opening setting for the end of the programme can be chosen in the SETUP procedures, see paragraph "SETUP MODE DESCRIPTION ". Rev. 00 GW2045 – GW1060 Manual Pag. 27 di 43... -
Page 29: In Progress Programme Interruption
To terminate, turn the programme selector knob (1) to position 8 and press the DOOR OPEN button • (6) for 4 seconds. The new DATE and TIME is now installed. Rev. 00 GW2045 – GW1060 Manual Pag. 28 di 43... -
Page 30: Communication With Printer
GW2045 – POSITION OF PORT RS232 fig. 8 - Rear of GW2045, detail of RS232 connection, where it is possible to connect the external printer. Position Rear cross section, left side. Rev. 00 GW2045 – GW1060 Manual... - Page 31 GW1060 – POSITION OF PORT RS232 fig. 9 - Rear of GW1060, detail of RS232 connection, where it is possible to connect the external printer. Rev. 00 GW2045 – GW1060 Manual Pag. 30 di 43...
-
Page 32: Operating Instructions
Load salt when necessary and before starting wash programme; in this way, any • excess saline solution is immediately removed by the water. A prolonged presence of salt water inside the wash vat may cause corrosion. Rev. 00 GW2045 – GW1060 Manual Pag. 31 di 43... -
Page 33: Use Of The Detergent And Neutralizing Agent
11 - Power detergent distributor DD. The distributor opens automatically during the wash. The recommended dose of the SMEG detergent Deterglass is 35-40 mg, an amount indicated by the reference lines on the inner border of the distributor. The MIN reference line is equivalent to 35 mg, that MAX line is 40 mg. -
Page 34: Loading Neutraliser
The amounts distributed by the peristaltic pumps can be regulated via the SETUP mode, see paragraph "SETUP MODE DESCRIPTION". SMEG recommends use of the following neutralising acids: Smeg Acidglass C, Smeg Acidglass C2 and Smeg Acidglass P. Acidglass C, C2: Citric acid-based. -
Page 35: Optional Accessories
There is a metal plate fixed with Philips screws on the rear, above the pumps. The terminal board is fixed to the inside of the plate, which allows electrical connection of the optional level sensors. fig. 13 - Rear of GW2045, position of pumps and detail of plate that holds electrical connection terminal board. GW1060 The optional peristaltic pump must be mounted on the rear, in the free space next to the pump P2. -
Page 36: Detergent Can Level Sensors
14 - Rear of 1060, position of pumps from top to bottom respectively. P1, P2, P3 7.5.2. DETERGENT CAN LEVEL SENSORS The machine can also be fitted with built-in level sensors in the detergent suction pipes, smeg product "KIT WD-LS3060". -
Page 37: Precaution When Using Detergents
DISPOSAL of any remaining product: consult the manufacturer, under "INFORMATION ON DISPOSAL". If you lose the sheets, they can be requested from SMEG S.p.A. instruments@smeg.it Rev. 00 GW2045 – GW1060 Manual... -
Page 38: Alarms
The actions described below are a brief summary that may be useful. These actions must not be taken by unauthorised staff. Contact Smeg Technical Assistance if the error remains after the RESET procedure or if a particular error reoccurs. ALARM ID... - Page 39 This malfunction can be temporary: Repeat the cycle. Unstable temperature Check that the temperature probe is functioning properly. Rev. 00 GW2045 – GW1060 Manual Pag. 38 di 43...
-
Page 40: Cleaning And Maintenance
H05V2-K, according to the nomination abbreviations on cables: "H": Harmonised with brand “HAR”. "05": Nominal voltage U /U 300/500V. "V2": PVC for temperature of 90° C. "-K": Flexible cable for fixed laying. Rev. 00 GW2045 – GW1060 Manual Pag. 39 di 43... - Page 41 How to clean the filter unit – GW2045 It is necessary to inspect the central filter “D” regularly, and if necessary, clean it. To extract it, it is necessary to grip the handle, turn it anticlockwise and lift it up as shown in the picture.
-
Page 42: If The Glassware Washer Is Not Used For A Long Period Of Time
Check that the salt tank top is closed correctly and the water softener system has been adjusted • correctly. Contact your nearest authorized technical assistance center if the faults persist after compliance with the instructions given above. Rev. 00 GW2045 – GW1060 Manual Pag. 41 di 43... -
Page 43: Installation Diagram Gw2045 - Gw1060
Repairs to the appliance by unauthorized personnel are not covered by the warranty and are at the user’s charge. INSTALLATION DIAGRAM GW2045 – GW1060 For detailed specifications and electricity connection, see paragraph "INSTALLATION". Note: Water connections can also be prepared on the left side of the machine, bearing in mind the maximum distance indicated on the product, “H”. - Page 44 Smeg S.p.A. Instruments Division Via Leonardo da Vinci, 4 Tel +39 0522 8211 – Fax +39 0522 821 592 E-mail: instruments@smeg.it – www.smeg-instruments.com...