Subscribe to Our Youtube Channel
Related Manuals for Otto Bock 490E163 Series
Summary of Contents for Otto Bock 490E163 Series
- Page 1 490E163=* Instructions for use (qualified personnel) ..............
- Page 2 490E163=*...
-
Page 3: Table Of Contents
Table of contents Table of contents Foreword ................................Intended use ................................ Indications for use ..........................Indications, contraindications ......................... Qualification ............................Safety ..................................Explanation of warning symbols ......................General safety instructions ........................Safety Instructions for Assembly ......................Programming safety instructions ......................Safety instructions regarding maintenance and repairs ................ - Page 4 Table of contents Information on re-use ........................... Legal information .............................. 10.1 Liability .............................. 10.2 Warranty ............................10.3 Lifetime .............................. Technical data ..............................Appendices ................................ 12.1 Required tools ............................ 12.2 Torque values of the screw connections ....................490E163=*...
-
Page 5: Foreword
Foreword 1 Foreword INFORMATION Date of last update: 2021-03-30 ► Please read this document carefully before using the product and observe the safety notices. ► Instruct the user in the safe use of the product. ► Please contact the manufacturer if you have questions about the product or in case of problems. ►... -
Page 6: General Safety Instructions
Safety 3.2 General safety instructions CAUTION Use of unsuitable tools Pinching, crushing or damaging the product due to use of unsuitable tools ► When completing the tasks, only use tools that are suitable for the conditions at the place of work and for which safety and the protection of health are assured with proper use. -
Page 7: Programming Safety Instructions
Safety NOTICE Incorrect cable routing Plug connections coming loose or damage to the cables due to assembly errors ► Take note of the cables attached to the product with cable ties during all assembly work. ► Carefully cut the cable ties with suitable side-cutting pliers if necessary. Ensure that you do not damage the cables during this process. -
Page 8: Delivery
Delivery Label Meaning M WARNING! Read the instructions for use before using the product. Observe important safety-related information (e.g. warnings, precautions). N Symbol for separate collection of electrical and electronic devices. Components of the power wheelchair and batteries may not be disposed of in household waste. O Manufacturer’s reference number for the product variant 3),1) P Serial number (PI) -
Page 9: Preparing The Product For Use
Preparing the product for use Note regarding the tyres • If the power wheelchair is not moved for several days, permanent colour changes may develop where it comes into contact with the ground. A suitable base should therefore be used when parking it for extended periods of time. -
Page 10: Attaching The Arm Supports
Settings and assembly instructions 5.4 Attaching the arm supports After unpacking, the arm supports have to be attached using the clamping pins (clamps) if applicable. See the power wheelchair instructions for use (user) for more detailed information. 6 Settings and assembly instructions 6.1 Prerequisites WARNING Making incorrect adjustments... -
Page 11: Lighting (Not Intended For Road Traffic)
Settings and assembly instructions Removing the battery cover 1) Disconnect the plug of the battery cable from the controller (see fig. 2, item 1). To release the plug, push the snap-fit (see fig. 2, item 2). 2) Loosen the four Allen screws on the battery cover (see fig. 2, item 3). -
Page 12: Lighting For Road Traffic
Settings and assembly instructions 6.2.3 Lighting for road traffic INFORMATION ► Before performing the work described below, remove the plug of the battery cable from the controller. Only reconnect it for the functional test. ► Leave the lighting set assembled as delivered for the installation described below. The lamps are already installed on the supplied cable of the lighting set. - Page 13 Settings and assembly instructions Installing the lamps 1) Set the cable of the lighting set with the connected lamps onto the battery cover under the seat, align ing them correctly. INFORMATION: You can disconnect the lamps from the cable of the lighting set for easier assembly.
-
Page 14: Control Panel Holder, Swing-Away In Parallel
Settings and assembly instructions Connecting the lighting push-button module and performing a functional test 1) Screw the two cable ends to the battery contacts. Connect the red cable to the red contact (see fig. 10, item 1). 2) Turn the cable end with the fuse so that the fuse can be positioned between the batteries (see fig. 10, item 2). -
Page 15: Foot Positioning Belt
Settings and assembly instructions 6.2.6 Foot positioning belt 1) Pass the threading device of the positioning belt (see fig. 13, item 1) through the outer slot of the foot plate from above (see fig. 13, item 2). Turn the end crosswise below the foot plate so it cannot slide back out of the slot (not illustrated). -
Page 16: Adapter For Head/Neck Support Mounting Kit
Settings and assembly instructions Installing the sternum harness on the upper back support tube 1) Pre-install two tube clamps on the back support tube, each at a distance approximately equal to the width of the belt straps (see fig. 15, item 1/2). 2) Pass the upper belt straps of the sternum harness around the back support tube between the tube clamps (see fig. 15, item 3). -
Page 17: Storage Bag
Settings and assembly instructions Installing the crutch holder component group on the anti-tipper 1) Remove the anti-tipper roller (see fig. 18, item 1). 2) Affix the supplied loop strap to prevent rattling (see fig. 18, item 2). 3) Slide the crutch holder component group onto the anti-tipper tube (see fig. 18, item 3). -
Page 18: Attaching Additional Options
Settings and assembly instructions Checking the storage bag 1) The front edge of the storage bag is approximately in line with the front edge of the battery cover (see fig. 21, item 1). 2) The magnetic closures can be readily applied to the frame tube. -
Page 19: Adjusting The Leg Support
Settings and assembly instructions Adjusting the width 1) Loosen the Allen head screws and move the arm pads to the desired position (see fig. 24, item 1). INFORMATION: The distance between the arm supports can be adjusted to 400 mm or 460 mm. Only the marked bore holes may be used (see fig. 24, item 1). -
Page 20: Adjusting The Control Panel Position
Settings and assembly instructions CAUTION Lack of instruction Injuries, malpositions, illness of the user due to incorrect information ► The qualified personnel is responsible for making sure that the user and/or attendant/care staff has under stood the proper adjustment, use, maintenance and care of the positioning belt (lap belt). ►... -
Page 21: Changing The Control Panel Side
Delivery 6.3.7 Changing the control panel side 1) Disconnect the battery cable from the controller (see page 9). 2) Only if necessary: Disconnect the connection plug of the control panel under the seat plate (see fig. 28, item 1). 3) Remove the cable holders on the arm support see fig. 28, item 2). -
Page 22: Transport To The Customer
Delivery • Do all power functions work properly (e.g. motors, lighting/direction indicators – if installed)? • Do all control functions work properly? • Do the brakes work? 7.2 Transport to the customer CAUTION Securing the power wheelchair insufficiently during transport Crushing, pinching of body parts due to failure to observe transportation instructions ►... -
Page 23: Maintenance And Repair
Maintenance and repair The following steps must be performed for the safe handover of the product: • Have the user get into the product and perform a trial seat fitting. Pay special attention to proper positioning according to medical considerations. •... -
Page 24: Warranty
Technical data 10.2 Warranty Further information on the warranty terms and conditions can be obtained from the qualified personnel that has fit ted this product or the manufacturer's service (see inside back cover for addresses). 10.3 Lifetime Expected lifetime: 3 years The design, manufacturing and requirements for the intended use of the product are based on the expected life... - Page 25 Technical data Dimensions and weights Minimum turning radius 740 mm (29.1") Turning circle**** 1080 mm (42.5") Ground clearance***** 80 mm (3.1") Caster wheel tyre size 8" Drive wheel tyre size 12.5" * Cannot be changed ** Measured to back support *** With 480 mm lower leg length **** = Three-point turn by 180°...
-
Page 26: Appendices
Appendices Electrical circuit* Operating voltage 24 V DC Motor power See nameplate on motor for precise information: 160 watts/200 watts (depending on country version) Lighting LED front light 24 V, maintenance-free LED rear light 24 V, maintenance-free Fuse 50 A fuse cable (nVR2) Battery charger 5 A; usually supplied by Ottobock; for details, see the included bat tery charger instructions for use * The product meets all requirements under ISO 7176-14. - Page 27 · www.ottobock.de 143441 Moscow Region/Krasnogorskiy Rayon info@ottobock.com.co · www.ottobock.com.co Russian Federation Otto Bock Healthcare Products GmbH Otto Bock de Mexico S.A. de C.V. T +7 495 564 8360 · F +7 495 564 8363 Brehmstraße 16 · 1110 Wien · Austria Prolongación Calle 18 No. 178-A info@ottobock.ru · www.ottobock.ru F +43 1 5267985...
- Page 28 Ihr Fachhändler | Your specialist dealer Otto Bock Mobility Solutions GmbH Lindenstraße 13 · 07426 Königsee/Germany www.ottobock.com...
Need help?
Do you have a question about the 490E163 Series and is the answer not in the manual?
Questions and answers